TS-10 Sti (Scientific Technologies, Inc.), TS-10 Datasheet - Page 5

• Manufacturer Part Number: TS-10
• Description: Touchstart Palm Button, 120VAC
• Manufacturer: Sti (Scientific Technologies, Inc.)

J
TouchStart
■
Specifications are subject to change without notice.
* If any of these values are exceeded, the TouchStart will default to a safe state (output relays de-energized). The TouchStart automatically resets when
conditions fall below the limit.
J6
■
model
TS-10
TS-20
TS-SQ
TS-R
TS-B1
TS-B2
to order a complete touchStart Palm button, two-hand control system,
order one of each of the following:
TS-10 or TS-20
TS-SQ or TS-R
TS-B1 or TS-B2
SR104P
max Wiring Size:
housing material:
Weight:
Actuation:
Power Supply
Power consumption:
indicator:
Output:
mechanical life:
electrical life:
mechanical Shock:
Vibration:
relative humidity:
noise Protection:
Weldfield immunity:
rfi:
Protection:
temperature range:
max response times:
Approvals:
contact ratings:
Specifications
Ordering
tS-10:
tS-20:
OmrOn Scientific technOlOgieS, inc.
USA
™
Tel. [phone]
Description
TouchStart Palm Button, includes mounting jam nut and gasket, 120 VAC
TouchStart Palm Button, includes mounting jam nut and gasket, 24 VDC
Plastic, square ring guard, mounting screws, spacers
Metal, round ring guard, mounting screws, spacers
Electrical box, with one conduit hub (3/4 in.), cover plate for box, gasket for box
Electrical box, with two conduit hubs (3/4 in.), cover plate for box, gasket for box
TouchStart Palm Button—order two each
Ring Guards or other shields must be installed to avoid accidental operation in
safety applications per OSHA and ANSI — order two each
Electrical box—order a total of two (one of each type or two of one type)
Anti-tie down relay — order one per system
canada
Tel. [phone]
tS-10 for 120 VAc; tS-20 for 24 VDc
14 AWG (1)
Nory lN190
313 g (11 oz.)
Hand sensitive requiring no pressure to initiate, operates with or without gloves
120 VAC ±10%, 45 to 60 Hz
24 VDC ±10%
≤1 W
Red LED, illuminates when relays are energized
Two relays provide 1 set of normally open contacts, 1 set of normally closed
contacts. Force-guided contacts are used.
1 A at 250 VAC max resistive; 1 A @ 90 VDC max resistive
Greater than 50 million operations
Greater than 5 million operations at loads less than 50 VA
45 g for 2 ms
4 g at f ≤60 Hz and amplitude ≤ 1 mm
≤ 99%
Bursts to 2 kV, spikes of 500V, electrostatic fields to 8 kV*
Resistor welding up to 50 kA AC/DC (in suitable enclosure)*
≤ 8 V/m
IP64
-18 to 50°C (0 to 122°F)
On = 60 ms; Off = 80 ms
CE marked for all applicable directives, UL and C-UL
For the Latest Information
On the Internet: www.sti.com or www.omron.ca
Warning!
personal injury or property dam-
age if it is not installed and used in
accordance with the manufacturer’s
instructions and in accordance with
regulations of the Occupational
Safety and Health Administration Part
1910.217, the procedures prescribed
by the American National Standards
Institute B11.1 and B11.19, and all
other applicable regulations, proce-
dures and codes. The manufacturer
shall not be responsible nor liable
for any injury or damage resulting
from use of the product in any such
applications or the failure to comply
with any such regulation, procedure
or code.
This product may cause substantial
A
Go to the Engineering Guide
For in-depth information on
safety standards and use.