IL410 Vishay / Small Signal & Opto Products (SSP), IL410 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
IL410
Manufacturer Part Number
IL410
Description
Optoisolator; Analog; 6-Pin DIP; TRIAC; 1.16 V; 60mA; 500 mW; 6 V
Manufacturer
Vishay / Small Signal & Opto Products (SSP)
Type
Analogr
Datasheet
1.IL410.pdf
(10 pages)
Specifications of IL410
Capacitance
25 pF
Current, Forward
60 mA
Input Type
LED
Output Type
Triac
Package Type
6-Pin DIP
Power Dissipation
500 mW
Special Features
Zero Crossing
Temperature, Operating, Maximum
150 °C
Temperature, Operating, Minimum
-55 °C
Time, Turn-off
50 μs
Time, Turn-on
35 μs
Voltage, Forward
1.16 V (Typ.)
Voltage, Reverse
6 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IL410
Manufacturer:
INFINEON
Quantity:
2 700
Part Number:
IL410
Manufacturer:
VISHAY/威世
Quantity:
20 000
Part Number:
IL410-X001
Manufacturer:
SIEMENS/西门子
Quantity:
20 000
Company:
Part Number:
IL410-X007T
Manufacturer:
VISHAY
Quantity:
5 621
Part Number:
IL410-X009T
Manufacturer:
VISHAY/威世
Quantity:
20 000
Company:
Part Number:
IL41050TA-3E
Manufacturer:
DELTA
Quantity:
1 000
Part Number:
IL41050TAE
Manufacturer:
NVE
Quantity:
20 000
Company:
Part Number:
IL41050TE
Manufacturer:
NVE
Quantity:
100
Company:
Part Number:
IL4106
Manufacturer:
INFINEON
Quantity:
5 510
Part Number:
IL4108
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
IL410/ IL4108
Vishay Semiconductors
connected to the line by transformers and which are not mechani-
cally interrupted.
In such cases as well as in applications with a resistive load the cor-
responding protective circuits can be neglected.
Control And Turn-On Behavior
The trigger current of the IL410/ IL4108 has a positive
temperature gradient. The time which expires from
applying the control current to the turn-on of the load
current is defined as the trigger delay time (t
the whole this is a function of the overdrive meaning
the ratio of the applied control current versus the trig-
ger current (I
corresponds to that of the individual trigger current of
IL410/4108 turn-on delay times amounts to a few mil-
liseconds only. The shortest times of 5.0 to 10 s can
be achieved for an overdrive greater or equal than 10.
The trigger delay time rises with an increase in tem-
perature.
For very short control current pulses (t
correspondingly higher control current must be used.
Only the IL410/ IL4108 without zero voltage switch is
suitable for this operating mode.
Zero Voltage Switch
The IL410/ IL4108 with zero voltage switch can only
be triggered during the zero crossing the sine AC volt-
age. This prevents current spikes, e.g. when turning-
on cold lamps or capacitive loads.
Applications
Direct switching operation: The IL410/ IL4108 switch
is mainly suited to control synchronous motors,
valves, relays and solenoids in Grätz circuits. Due to
the low latching current (500 A) and the lack of an
RC circuit at the output, very low load currents can
easily be switched.
Indirect switching operation: The IL410/ IL4108
switch acts here as a driver and thus enables the driv-
ing of thyristors and triacs of higher performance by
microprocessors. The driving current pulse should not
exceed the maximum permissible surge current of the
IL410/ IL4108. For this reason, the IL410/ IL4108
without zero voltage switch often requires current lim-
iting by a series resistor.
The favorably low latching current in this operating
mode results in AC current switches which can handle
load currents from some milliamperes up to high cur-
rents.
www.vishay.com
8
F
/I
FT
). If the value of the control current
plF
< 500 s) a
gd
). On
Application Note
• Over voltage protection: A voltage-limiting varistor
(e.g. SIO VS05K250) which directly connected to the
IL410/ IL4108 can protect the component against
overvoltage.
Document Number 83627
Rev. 1.4, 26-Apr-04