PR03000201202JAC00 BC Components / Vishay, PR03000201202JAC00 Datasheet - Page 13

• Manufacturer Part Number: PR03000201202JAC00
• Description: Resistor; Metal Film; Res 12 Kilohms; Pwr-Rtg 3 W; Tol 5%; Axial; Ceramic Housed
• Manufacturer: BC Components / Vishay

Specifications of PR03000201202JAC00

• Brand/series: PR03
• Diameter, Lead Wire: 0.78 ± 0.05 mm
• Dimensions: 5.2 mm (Max.) Dia. x 19.5 mm (Max.) L
• Material, Element: Metal Film
• Package Type: Ceramic Housed
• Power Rating, Test Condition: @ +70°C
• Power, Rating: 3 W
• Resistance: 12 Kilohms
• Temperature Coefficient, Resistance: ± 250 ppm⁄K (Max.)
• Temperature, Operating: +250 °C (Max.)
• Termination: Axial
• Tolerance: ±5 %
• Voltage, Rating: 750 VDC
• Lead Free Status / Rohs Status: RoHS Compliant part

PR01/02/03
Vishay BCcomponents
Application Information
TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
schedule
LCT/UCT/56 (rated temperature range: Lower Category
Temperature, Upper Category Temperature; damp heat,
long
requirements specified by EIA and EIAJ.
The tests are carried out in accordance with IEC publication
60068-2, “Recommended basic climatic and mechanical
robustness testing procedure for electronic components” and
www.vishay.com
122
TEST PROCEDURES AND REQUIREMENTS
TESTS IN ACCORDANCE WITH THE SCHEDULE OF IEC PUBLICATION 60115-1
4.4.1
4.4.2
4.5
4.18
4.29
4.17
4.7
CLAUSE
60115-1
IEC
term, 56 days).
of
METHOD
60068-2
45 (Xa)
TEST
20 (Tb)
20 (Ta)
IEC
“IEC publication
ϕ(deg)
- 30
- 60
- 90
90
60
30
0
1
(refer note on first page
for measuring distance)
resistance to soldering heat
dimensions (outline)
The
component solvent
visual examination
voltage proof on
solderability
resistance
resistance
insulation
TEST
testing
For technical questions, contact: [e-mail]
60115-1”,
PR03 Phase angle as a function of applied frequency
also
Power Metal Film Resistors
thermal shock: 3 s; 350 °C; 3 mm from body
covers
10
category
during 1 min; metal block method
in accordance with “MIL 202 F”
applied voltage (+ 0/- 10 %):
maximum voltage 500 V
isopropyl alcohol or H
10 kΩ ≤ R < 100 kΩ: 10 V
the
100 kΩ ≤ R < 1 MΩ: 25 V
10 Ω ≤ R < 100 Ω: 0.3 V
followed by brushing
100 Ω ≤ R < 1 kΩ: 1 V
1 kΩ ≤ R < 10 kΩ: 3 V
PROCEDURE
R < 10 Ω: 0.1 V
R = 1 MΩ: 50 V
gauge (mm)
2 s; 235 °C
under standard atmospheric conditions according to
“IEC 60068-1”, subclause 5.3.
In the Test Procedures and Requirements table, tests
and requirements are listed with reference to the relevant
clauses of “IEC publications 60115-1 and 60068-2”; a short
description of the test procedure is also given. In some
instances deviations from the IEC recommendations were
necessary for our method of specifying.
All soldering tests are performed with mildly activated flux.
2
RMS
O
10
2
R
R
R
R
R
n
n
n
see Straight and Kinked Dimensions tables
n
n
= 18 Ω
= 1.5 Ω
= 20 k Ω
= 100 k Ω
= 1.3 k Ω
no holes; clean surface; no damage
ΔR max.: ± (1 % R + 0.05 Ω)
no breakdown or flashover
good tinning; no damage
R - R
f (MHz )
REQUIREMENTS
no visual damage
nom
Document Number: 28729
: max. ± 5 %
10
3
Revision: 21-Feb-08