VQ110-5F SMC Corporation, VQ110-5F Datasheet - Page 2

• Manufacturer Part Number: VQ110-5F
• Description: Valve, compact, 3 port, NC, 24VDC, plug-in, non-locking push style override
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ110-5F

• Brand/series: VQ Series
• Configuration: 2-Position Single
• Flow Type: Air/Inert Gas
• Number Of Ports: 3
• Orientation: Unrestricted
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to + 50°C
• Valve Type: Compact 3 Port Valve, Normally Closed, Standard, Non-Locking Push Style
• Voltage, Coil: 24 VDC

If the manual override is manipulated, since any connected
equipment will be activated, make sure to be done only after no
danger is confirmed.
í Non-locking push type (Tool required)
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
í Locking type (Tool required)
í Push-locking type
Caution
Warning
Note) Ensure the locking type manual override is unlocked before
using.
When operating the lock with the driver, use a watchmakers’
screwdriver and turn lightly.
[Torque 0.1 N·m or less]
Manual Override Operation
(Tool required)
• It is turned ON by pushing the button in the
• If the manual override is turned clockwise and
• If
• If the manual override is turned clockwise and
• If
direction indicated by the arrow until it hits the
end and is turned OFF by releasing the button.
the
the reset condition. (Passage P
counterclockwise and the
to 0, it will be back to the reset condition.
(Passage A
shipment.)
the
the ON state.
counterclockwise and
locking will be released and the manual
override will return.
the
the
<
mark is adjusted to 1, it will be backed to
mark is adjusted to 1, it will be locked in
Option
0
0
TURN PUSH
TURN PUSH
manual
manual
ON
Set
<
Latching type
>
R) (Reset state at the time of
1
1
override
override
0
TURN PUSH
0
mark is adjusted to 0,
Reset
TURN
OFF
mark is adjusted
>
is
A)
is
1
1
Precautions
turned,
turned
Crimping of lead wires and sockets
Peel 3.2 to 3.7 mm of the tip of lead wire, enter the core wires
neatly into a socket and crimp it with a special crimp tool. Be
careful so that the cover of lead wire does not enter into the
crimping part. (Crimping tool part no.: DXT170-75-1)
Attaching and detaching lead wires with sockets
Attaching and detaching connectors
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or
To detach a connector, remove the pawl from the groove by
Attaching
Insert the sockets into the square holes of the connector (with
A, C, and B indication) and continue to push the sockets all the
way in until the lock by hooking into the seats in the connector.
(When they are pushed in, their hooks open and they are
locked automatically.) Then confirm that they are locked by
pulling lightly on the lead wires.
Detaching
Pull and detach the lead wire, pressing in on the end of the
hook of the socket through the side hole using a stick with thin
end (about 1 mm). To reuse the socket, extend the hook
outward.
To attach a connector, hold the lever and connector unit
between your fingers and insert straight onto the pins of the
solenoid valve so that the lever’s pawl is pushed into the
groove and locks.
pushing the lever downward with your thumb, and pull the
connector straight out.
Core wire
crimping area
Socket
Caution
disconnection.
Hook
Socket
How to Use Plug Connector
Pin
Cover
Convex
part
Crimping area
Hook
Convex
part
Pin
Lever
Core wire
Hook
Insulation
Lead wire 0.2 to 0.33 mm
Socket
Part no. DXT170-71-1
Series
Connector
Part no. AXT661-12
Lead wire
0.2 to 0.33 mm
(Max. cover diameter:
(Max. cover diameter:
VQ100
Lead wire
Connector
2
2
ø
ø
1.7 mm)
1.7 mm)
4-12-3
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN