MAX913CSA+ Maxim, MAX913CSA+ Datasheet - Page 3

• Manufacturer Part Number: MAX913CSA+
• Description: Comparator, Low Power; TTL +/- 7V; 6 mA (Typ.) (Positive)/1 mA (Typ.) (Negative)
• Manufacturer: Maxim
• Type: Low Power, Precisionr

Specifications of MAX913CSA+

• Amplifier Type: Comparator
• Common Mode Rejection Ratio: 110
• Current, Input Bias: 2 μA
• Current, Input Offset: 0.3 μA
• Current, Supply: 6 mA
• Number Of Amplifiers: Single
• Package Type: SOIC-8
• Power Dissipation: 471 mW
• Propagation Delay: 10 ns
• Temperature, Operating, Range: 0 to +70 °C
• Voltage, Gain: 3500 V/V
• Voltage, Input: -0.3 to +14 V
• Voltage, Input Offset: 0.1 mV
• Voltage, Supply: ±5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

ELECTRICAL CHARACTERISTICS (continued)
V+ = +5V, V- = -5V, V
Note 1: All specifications are 100% tested at T
Note 2: Input Offset Voltage (V
Note 3: Supply currents are measured with V
Note 4: Propagation Delay (t
Note 5: Input latch setup time (t
Note 6: Latch Propagation Delay (t
Propagation Delay (Note 4)
Differential Propagation Delay
(Note 4)
Channel-to-Channel Propagation
Delay (Note 4)
Latch Setup Time (Note 5)
Latch Hold Time (Note 5)
Latch Propagation Delay (Note 6)
to T
then the other to 1.4V. Input Offset Current (I
with low input overdrive values. Characterization and correlation tests have shown that t
teed by design. Electrical Characteristic DC tests are performed to guarantee that all internal bias conditions are correct.
For low overdrive conditions, V
time (t
by design.
Timing Diagram).
PARAMETER
MAX
H
) is the interval after the latch is asserted in which the input signal must be stable. These parameters are guaranteed
) are guaranteed by design.
_______________________________________________________________________________________
Q
= 1.4V, V
PD
OS
) and Differential Propagation Delay ( t
SU
LE
) is defined as the average of the two input offset voltages, measured by forcing first one output,
) is the interval in which the input signal must be stable prior to asserting the latch signal. The hold
= 0V, T
LPD
Single/Dual, Ultra-Fast, Low-Power
SYMBOL
t
PD+
OS
) is the delay time for the output to respond when the latch-enable pin is deasserted (see
t
t
LPD
t
t
SU
H
, t
PD
is added to overdrive. Differential Propagation Delay is defined as t
A
PD-
= T
Q
A
driven to both V
MIN
= +25°C, unless otherwise noted. Specification limits over temperature (T
V
V
V
V
(MAX912 only)
V
V
V
V
OD
OD
OD
OD
to T
IN
IN
IN
IN
OS
= 5mV
= 20mV
= 5mV
= 5mV
= 100mV,
= 100mV,
= 100mV,
= 100mV,
) is defined the same way.
MAX
Precision TTL Comparators
, unless otherwise noted. Typical values are at T
OH
CONDITIONS
and V
T
T
T
T
T
T
A
A
A
A
A
A
= +25°C
= T
= +25°C
= T
= +25°C
= +25°C
OL
PD
MIN TO
MIN TO
) cannot be measured in automatic handling equipment
(not 1.4V).
T
T
MAX
MAX
MAX913
MAX912
MIN
PD
2
5
and t
TYP
500
PD
10
A
3
9
2
0
2
7
= +25°C.) (Note 1)
PD
limits can be guaran-
= t
MAX
PD+
14
16
12
15
4
5
- t
PD-
A
UNITS
= T
.
ps
ns
ns
ns
ns
ns
MIN
3