ZSE30-T1-65-L SMC Corporation, ZSE30-T1-65-L Datasheet - Page 3

• Manufacturer Part Number: ZSE30-T1-65-L
• Description: Switch, VACUUM, PNEUMATIC, -100 TO 100 KPA, 12-24VDC IN, 80MA PNP OUT, 1/8IN. PORT
• Manufacturer: SMC Corporation

Specifications of ZSE30-T1-65-L

• Adjustment Range: -101 to 101 kPa
• Current, Consumption: 45 mA
• Current, Rating: 80 mA
• Enclosure Type: IP40
• Length, Wire: 2 m
• Output Type: PNP
• Pressure, Operating: -100.0 to 100.0 kPa
• Repeatability: ± 0.2% F.S. ± 1 Digit or Less
• Resistance, Insulation: 50 Megohms
• Size, Port: NPT 1⁄8
• Standards: Compliant with CE Marking and UL (CSA)
• Temperature, Ambient: 25 °C
• Voltage, Rating: 12 to 24 VDC
• Voltage, Withstanding: 1000 VAC for 1 Minute

Pressure setting
Manual setting
Window comparator mode
Hysteresis mode
Pressure set value can be verified without holding or stopping
the switch output operation.
Press the SET button in the measuring mode to display the
set value.
Press the SET button to display the next set value. Press the
to Set Value” on the lower right hand corner of this page.)
In this mode, P2 and the current set value are displayed
alternately after setting P1. Press the SET button to display
the next set value ( : hysteresis). Press the
button to change the value.
(Refer to “How to Set Value” at right.)
Next,
alternately. Press the SET button to return to the normal
measuring mode. Press the
change the value.
(Refer to “How to Set Value” at right.)
In this mode, hysteresis (H) and the set value for hysteresis
are displayed alternately after setting P1. Press the SET
button to return to the normal measuring mode. Press the
(Refer to “How to Set Value” below right.)
UP or
UP or
Normally Closed
Normally Open
OUT
OUT
and the set value for hysteresis will be displayed
PRESSURE
PRESSURE
DOWN button to change the value.
DOWN button to change the value. (Refer to “How
and the current set value blink alternately.
2-color Display Digital Pressure Switch
Alternately
displayed
UP or
OUT
DOWN button to
PRESSURE
UP or
DOWN
High Precision,
Auto preset setting
1.
2.
How to Set Value
To enter a value such as the one for pressure setting:
Auto preset preparation mode
While in the measuring mode, press the SET button to
activate the auto preset preparation mode, and
displayed. Proceed to prepare the devices to perform the
pressure setting. While
measuring mode.
Auto preset setting
Press the SET button to activate the mode to execute auto
preset functions. When
operation and change the pressure. The set value will be
automatically detected and stored.
While
the setting and return to the normal measuring mode.
1. Press the
2. Press the
3. With every push of the SET button, the next (higher)
4. Press and hold the SET button for 1 second or longer
UP and
value. The first digit blinks.
arbitrarily. (If there is no button operation for more than
10 seconds, the current value will be automatically set
and the function will return to the set value display
mode.)
digit blinks.
When the left-most digit is zero, “ ” or “ ” will blink.
If the SET button is pressed while the left-most digit is
blinking, the right-most digit will now blink.
to return to the set value display mode.
Series
is still displayed, press the SET button to complete
DOWN buttons simultaneously to return to the
2nd digit
UP or
UP or
OUT
OUT
ZSE30/ISE30
PRESSURE
PRESSURE
DOWN button to change the set
DOWN button to set the value
is still displayed, press both the
is displayed, start the system
1st digit
3rd digit
16-2-7
will be
„
„
„
„
„