I2000 FLEX Fluke, I2000 FLEX Datasheet

no-image

I2000 FLEX

Manufacturer Part Number
I2000 FLEX
Description
Probe, AC Current; 20 to 2000 A ac; -3 dB 1 Hz to 20 kHz; lt 2 mV rms
Manufacturer
Fluke
Type
Current Clampr
Datasheet
1.I2000_FLEX.pdf (2 pages)

Specifications of I2000 FLEX

Bandwidth
-3 dB 1 Hz to 20 kHz
Current, Rating
20 to 2000 A ac
Standards
CE Certified
Temperature, Operating
-20 to +90 °C
Two Ranges
200 A & 2000 A, 1 or 10 mV/A output
Lead Free Status / Rohs Status
RoHS Exempt Product
Introducing the i2000flex
The i2000flex is a flexible AC current probe for use with
oscilloscopes and multimeters. The supplied Dual Banana to BNC
Adapter can be used for connection to instruments with banana
inputs. The i2000flex is optimized for current measurement on thick
and hard to reach conductors.
Unpacking
The following items should be included in the package:
Check the contents of the shipping box for completeness. If
something in the box has been damaged or missing, contact your
distributor or the nearest FLUKE sales or service office
immediately.
Using the i2000flex Safely
In this Instruction Sheet, a Warning identifies conditions and
actions that pose hazard(s) to the user. A Caution identifies
conditions and actions that may damage the current probe.
International electrical symbols used are explained below.
February 1998
© 1998 Fluke Corporation.
All rights reserved.
Printed in the Netherlands
All product names are trademarks of
their respective companies.
2000A Flexible AC Current Probe
i2000flex Current Probe
Dual Banana to BNC Adapter (model PM9081/001)
Instruction Sheet (this paper)
To prevent electric shock, fire, and personal injury,
carefully read all safety information before
attempting to operate the Current Probe and follow
these procedures.
Before each use, inspect the Current Probe and its latching
system for any damage. Pay particular attention to the
insulation surrounding the flexible measuring head.
Do not use the Current Probe if it is damaged.
Do not use the Current Probe on circuits rated higher than
600V in Installation Category III (See "Specifications",
subsection “SAFETY”.)
Do not use the Current Probe to measure bare conductors
carrying a voltage from 30V up to 600V unless you are
wearing protective clothing suitable for high-voltage work.
Always use appropriate equipment for personal protection.
Do not expose the i2000flex unit to water.
See explanation in
the Instruction
Sheet
Double Insulation
(Protection class)
Warning
Instruction Sheet
i2000flex
Conformité
Européenne
®
Specifications
SAFETY
ELECTRICAL SPECIFICATIONS
Measuring range
Crest factor *)
Maximum non-
destructive current:
Output signal
Basic accuracy
Noise
Additional errors:
Phase shift
GENERAL
EMC
CE Conformity
All Electrical Specifications are valid at the following reference
conditions:
Bandwidth (-3dB)
Battery
Battery life
Indicators (see Figure 1)
Coupling diameter
Weight
Transducer length
Transducer diameter
Minimum bending radius
Cable length from transducer to
box
Cable length from box to BNC
output
Maximum extension cable length
Weight (without battery)
*)
value of a superimposed transient and the ac rms value.
with temperature
(0 to +70 °C,
32 to 158 °F)
with position of
conductor in the
probe window
with external fields
(< 40 A/m)
Ambient temperature
Relative Humidity
Frequency
Continuous external field
Load impedance on BNC
output
The current may not contain any DC component
No influence from adjacent currents
Conductor centered within the probe aperture
“POWER ON” indicator flashing (green LED)
“BATTERY LOW” indicator not flashing (red LED)
(see Figure 1)
i2000flex
(INPUT and OUTPUT)
This is the maximum permissible ratio between the peak
50 to 60 Hz
Power On
Battery Low
2 to 200A ac
up to 1.6
100 kA
10 mV/A
±1% of full scale
< 2 mV rms
(200 mA rms)
0.02% of
0.036% of
±2% of full scale
(bus
inch from coupling)
±1% of full scale
(adjacent conductor
from head.)
See Figure 2
< ±0.5°
reading /°C,
reading /°F
20 cm or 8 inch
200A
2.5 cm or 1
Meets requirements of:
Meets requirements of:
23±3°C (73±5.4°F)
0 to 85%
48 to 65 Hz
< 40 A/m
> 1 k // < 100 pF
1 Hz to 20 kHz
9V alkaline IEC 6LR61,
550 mAhr
> 100 hr
Green LED flashing
Red LED flashing
420 g (14.8 oz)
60 cm (31.5 in)
14.3 mm (0.563 in)
38 mm (1.5 in)
1.8 m (71 in)
0.5 m (19.7 in)
15 m (50 ft)
420 gr (14.8 oz)
Current Ranges
EN 61010-1,
UL3111,
for 600V
CAT III, pollution degree 2.
EN 50081-1
EN 50082-2
22.2 mm (0.874 in)
20 to 2000 A ac
up to 1.6
100 kA
1 mV/A
±1% of full scale
< 2 mV rms
(2A rms)
0.02% of
0.036% of
±2% of full scale
(bus
inch from coupling)
±1% of full scale
(adjacent conductor
from head.)
See Figure 3
< ±0.5°
reading /°C,
reading /°F
20 cm or 8 inch
2000A
2,5 cm or 1
*) Note: When the battery is almost completely empty, none of
Flashing when the
Temperature operating:
Temperature non-operating:
Relative Humidity
Altitude
Current Ranges
Transducer
i2000flex unit
Transducer and
i2000flex unit
Operating
Non-operating
Operating
Non-operating
Flashing when a
current range is
weak for correct
battery is too
measurement
selected. *)
Power off
results. *)
the LEDs will flash.
{
Figure 1. Text on the i2000flex unit
-20 to +90°C (-4 to +194°F)
0 to + 70°C (32 to +158°F)
-40 to + 105°C (-40 to +221°F)
0 to 85%, < +35°C (+95°F)
0 to 75%, < +90°C (+194°F)
0 to 85%, < -10°C (+14°F)
0 to 75%, < +105°C (+221°F)
to 3000 m (10000 ft)
to 12000 m (40000 ft)
PHASE SHIFT
Figure 3. Phase Shift versus Frequency (2000A range)
Figure 2. Phase Shift versus Frequency (200A range)
-10.0
-12.0
-14.0
-10.0
-12.0
-14.0
-2.0
-4.0
-6.0
-8.0
-2.0
-4.0
-6.0
-8.0
2.0
0.0
2.0
0.0
1
1
10
10
2000A Range
200A Range
Frequency (Hz)
Frequency (Hz)
100
100
1000
1000
10000
10000
100000
100000

I2000 FLEX Summary of contents

Page 1

... Dual Banana to BNC Adapter (model PM9081/001) Instruction Sheet (this paper) Check the contents of the shipping box for completeness. If something in the box has been damaged or missing, contact your distributor or the nearest FLUKE sales or service office Measuring range immediately. Crest factor *) Maximum non- ...

Page 2

... Set the unit switch to OFF. LIMITED WARRANTY & LIMITATION OF LIABILITY Disconnect the unit from the measurement instrument. This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from Note: accident, neglect, misuse or abnormal conditions of operation or The i2000flex unit contains an alkaline battery ...