E3T-FD11 Omron Automation, E3T-FD11 Datasheet
![no-image](/images/no-image-200.jpg)
E3T-FD11
Specifications of E3T-FD11
Available stocks
Related parts for E3T-FD11
E3T-FD11 Summary of contents
Page 1
... IC chips without covering them in resin, is what makes the slim structure of the E3T-FL possible. The E3T-FL is just 3.5 mm wide, even with a two-part light receiving element on the surface Rear of the circuit board and a signal processing IC on the rear. ...
Page 2
... E3T-SR Retro-reflective Models (Side-view) System Two models for different reflector characteristics. E3T-SR2@: With E39-R4, Sensing distance: 200 mm E3T-SR3@: With E39-R37, Sensing distance: 100 mm E3T-FD Diffuse-reflective Models (Flat) Minimum detection object: 0.15 mm dia. Only 3.5 mm wide for installation in small gaps. Sensor Protection Against Wiring ...
Page 3
... E3T-FT12 E3T-FT14 *3 E3T-FT21 E3T-FT23 *3 E3T-FT22 E3T-FT24 *2*3 E3T-SR21 E3T-SR23 *2*3 E3T-SR22 E3T-SR24 *2*3 E3T-SR31 E3T-SR33 *2*3 E3T-SR32 E3T-SR34 *2*3 E3T-FD11 E3T-FD13 *2*3 E3T-FD12 E3T-FD14 *2*3 E3T-SL11 E3T-SL13 *2*3 E3T-SL12 E3T-SL14 *2*3 E3T-SL21 E3T-SL23 *2*3 E3T-SL22 E3T-SL24 *2*3 E3T-FL11 E3T-FL13 *2*3 E3T-FL12 ...
Page 4
... Quantity Remarks Plug-in type round slits Can be used with E3T-ST@@ Through-beam Models. Plug-in type round slits Can be used with E3T-FT@@ Through-beam Models. Remarks Provided with the E3T-SR2@ Retro-reflective Models. 1 Provided with the E3T-SR3@ Retro-reflective Models. Model Quantity ...
Page 5
... Lens Denatured polyarylate Instruction manual, Installation phillip screws (Side-view Models: M2 × 14, Flat Models: M2 × 8), Nuts, Spring washers, Flat Accessories washers, E39-R4 (E3T-SR2@ only), E39-R37 (E3T-SR3@ only) * Values in parentheses indicate the minimum required distance between the Sensor and Reflector. Through-beam Flat NPN ...
Page 6
... Diffuse-reflective Flat NPN PNP Sensing method E3T-FD11 E3T-FD13 E3T-FD12 E3T-FD14 Sensing distance (50 × white paper) Standard sensing --- object Minimum detect- 0.15-mm dia. (sensing distance of 10 mm) able object (typical) Hysteresis 6 mm max. (white paper) Black/white error --- Directional angle --- Light source Red LED (“Pin-point” LED) λ = 650 nm ...
Page 7
... Load (Control output) Sensor (relay) max. Blue Main 3 Circuit 0 V Connector Pin Arrangement M12 e-CON Brown VDC 3 3 Blue 4 3 Note:Pin 2 is not used. Pins 2 and 4 are not used with Through-beam Emitters. Application 1 Power supply (+V) 2 --- 3 Power supply ( Output E3T 12 ...
Page 8
... Dimensions Sensors Through-beam Models (Side-view) E3T-ST1@ (Emitter) E3T-ST2@ (Emitter) R2.5 7 2.7 Emitter 4.8 Emitter: E3T-ST@@-L 6.6 Receiver: E3T-ST@@-D E3T-ST1@ (Receiver) E3T-ST2@ (Receiver) 7 Stability R2.5 3.1 Operation indicator indicator* 3.45 2.7 Receiver Lens (1.3 dia.) 4.8 6.6 Through-beam Models (Flat) E3T-FT1@ (Emitter) ...
Page 9
... M12 Smartclick Pre-wired Connector Model (E3T-SL@@-M1TJ) 6.3 5.2 2.4-dia. vinyl-insulated round cable with conductors Standard length: 0.3 m E3T Two, M2 e-CON Pre-wired Connector (E3T-SR@@-ECON) 5.9 1 ±0 15.6 2.4-dia. vinyl-insulated round cable with 3 conductors Standard lengths: 0.3 m and 2 m ...