SV1100-5FU SMC Corporation, SV1100-5FU Datasheet - Page 4

• Manufacturer Part Number: SV1100-5FU
• Description: Solenoid Valve, 5 port, 2 posit single, 24VDC, ind light, surge suppr
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of SV1100-5FU

• Brand/series: SV Series
• Configuration: 2-Position Single
• Primary Type: Solenoid Valve
• Voltage, Coil: 24 VDC

Connector entry directions for D-sub connectors and flat ribbon
cables can be changed. To change the connector’s entry
direction, press the levers on both sides of the connector, take it
off, and change the direction as shown in the drawing. Since lead
wire assemblies are attached to the connector, excessive pulling
or twisting can cause broken wires or other trouble. Also, take
precautions so that lead wires are not caught and pinched when
installing the connector.
The letter “S” or “D” is indicated on manifold blocks for series SV
as shown below. This indication refers to the type of substrate
assembly (single wiring or double wiring) inside the manifold
blocks.
When the manifold specification sheet does not include a wiring
specification, all stations will be double wiring specification (D). In
this case, single and double solenoid valves can be mounted in
any position, but when a single valve is used, there will be an
unused control signal. To avoid this, indicate positions of manifold
blocks for single wiring specification (S) and double wiring
specification (D) on a manifold specification sheet. (Note that
double, 3 or 4 position valves cannot be used for manifolds blocks
with single wiring specification (S).)
Substrate assemblies inside of manifolds cannot be taken apart.
Attempting to do so may damage parts.
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 1-7-2.
Wiring
specifications
symbol
Caution
Caution
Caution
Substrate Assemblies inside Manifolds
Connector Entry Directions
How to Order Manifold
Lever
Precautions 2
Lever
1. Tube attachment/detachment for One-touch fittings
1. When using tube other than SMC brand, confirm that
Valves with built-in back pressure check valve is to protect the
back pressure inside a valve. For this reason, use caution the
valves with external pilot specification cannot be pressurized from
exhaust port [3/5(E)]. As compared with the types which do not
integrate the back pressure check valve, C value of the flow
characteristics goes down. For details, please contact SMC.
1) Attaching of tube
2) Detaching of tube
the following specifications are satisfied with
respect to the outside diameter tolerance of the tube.
1) Nylon tubing
2) Soft nylon tubing
3) Polyurethane tubing within +0.15 mm
Do not use tubing which does not meet these outside diameter
tolerances. It may not be possible to connect them, or they may
cause other trouble, such as air leakage or the tube pulling out
after connection.
Back Pressure Check Valve Built-in Type
(1) Take a tube having no flaws on its periphery and cut it off
(2) Grasp the tube and push it in slowly, inserting it securely
(3) After inserting the tube, pull on it lightly to confirm that it
(1) Push in the release button sufficiently, and push the
(2) Pull out the tube while holding down the release button
(3) When the removed tube is to be used again, cut off the
Caution
Caution
Caution
at a right angle. When cutting the tube, use tube cutters
TK-1, 2 or 3. Do not use pinchers, nippers or scissors,
etc. If cutting is done with tools other than tube cutters,
there is the danger that the tube may be cut diagonally or
become flattened, etc., making a secure installation
impossible, and causing problems such as the tube
pulling out after installation or air leakage. Also allow
some extra length in the tube.
all the way into the fitting.
will not come out. If it is not installed securely all the way
into the fitting, this can cause problems such as air
leakage or the tube pulling out.
collar evenly at the same time.
so that it does not come out. If the release button is not
pressed down sufficiently, there will be increased bite on
the tube and it will become more difficult to pull it out.
portion which has been chewed before reusing it. If the
chewed portion of the tube is used as is, this can cause
trouble such as air leakage or difficulty in removing the
tube.
Other Tubing Brands
One-touch Fittings
within ±0.1 mm
within ±0.1 mm
within –0.2 mm
Series
SV
1-2-9
SV
SZ
SY
SYJ
SX