CW8100 Chemtronics, CW8100 Datasheet - Page 4

• Manufacturer Part Number: CW8100
• Description: Dispensing Pen, Flux; 0.32 Oz.
• Manufacturer: Chemtronics
• Type: Flux Dispensingr

Specifications of CW8100

• Application: All soldering applications where rosin or no clean flux is required
• Chemical Component: Adiptic Acid/Dimethyl Glutarate/Isopropanol/Rosin
• Dispensing Method: Pen
• Primary Type: Coating
• Special Features: No-Clean
• Weight: 0.32 Oz.
• Lead Free Status / Rohs Status: RoHS Compliant part Hazardous Materials

ITW CHEMTRONICS
SECTION 10: STABILITY AND REACTIVITY
Stability - This product is stable.
Conditions to Avoid: Do not use near open flames, red hot surfaces or other sources of ignition.
Incompatibility: Do not mix with strong acids or strong oxidizing agents.
Products of Decomposition: Thermal decomposition may release carbon monoxide, carbon dioxide and incompletely burned hydrocarbons.
Hazardous Polymerization: Will not occur.
SECTION 11: TOXICOLOGICAL INFORMATION
Toxicological Information
Inhalation:
Isopropanol
Skin:
Isopropanol
Cancer Information: No ingredients listed as human carcinogens by NTP or IARC
Reproductive effects: none
SECTION 12: ECOLOGICAL INFORMATION
Environmental Impact Information
Avoid runoff into storm sewers and ditches which lead to waterways. Water runoff can cause environmental damage.
REPORTING
US regulations require reporting spills of this material that could reach any surface waters. The toll free number for the US Coast Guard National Response Center is:
1-800-424-8802
SECTION 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with all federal, state and local regulations. Water runoff can cause environmental damage.
SECTION 14: TRANSPORTATION INFORMATION
Air:
Ground:
SECTION 15: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION
This product contains no toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986
(40 CFR 372).
This information should be included on all MSDSs copied and distributed for this material.
TOXIC SUBSTANCES CONTROL ACT (TSCA).
All ingredients of this product are listed on the TSCA Inventory.
WHMIS: Class B2; Class D2B
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the information required by the CPR.
SECTION 16: OTHER INFORMATION
N Product should be used only with adequate ventilation. Mechanical ventilation is recommended on all soldering stations. If such ventilation is not available, personnel
should wear NIOSH approved organic vapor respirators equipped with particulate dust filters specified for use during welding or soldering.
To the best of our knowledge, the information contained herein is accurate. However, all materials may present unknown hazards and should be used with caution. In
particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be
anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that may exist.
Proper
Shipping Name
Flammable liquid n.o.s.
(Isopropanol)
Consumer Commodity
ORM-D
®
Rabbit LD50
LC50/rats
Teratogenic effects: none
UN Number
UN 1993
NA
12,800 mg/kg
12,000 ppm/8hr
Class
NA
3
Page 2 of 2
Sub.
Risk
NA
--
Mutagenic effects: none
Ingestion:
Isopropanol
Eye:
Isopropanol
Pkg.
Group
II
NA
Hazard
Label
Flammable
liquid
ORM-D
rabbit
LD50 rats 5,045 mg/kg
Pkg.
173.150
Instr./Auth
305
MLD-MOD
MSDS #3112
Quantity
Max.
1L