EMV 1200-40 Lascar Electronics, EMV 1200-40 Datasheet

EMV 1200-40

Manufacturer Part Number

EMV 1200-40

Description

Meter, 2-Wire; Digital Meter Type; 3 VDC (Min.); 200; LCD; 0.5 in.; 3 mA

Manufacturer

Lascar Electronics

Type

Voltager

Datasheet

1.EMV_1200-40.pdf (1 pages)

Specifications of EMV 1200-40

Accuracy

0.4V V

Connection Type

2-Wire

Dimensions

1.73"W×0.82"H

Display Digit Height

0.5 "

Display Resolution

200 mVDC

Display Type

LCD

Function

Voltage

Meter Type

Digital

Power Consumption

3 mA

Primary Type

Electronic

Range, Measurement

40 to 40 VDC

Special Features

Splashproof

Temperature, Operating

0 to +50 °C

Voltage, Input

3 VDC

Voltage, Supply

50 VDC

Lead Free Status / Rohs Status

RoHS Compliant part

Current page: 1 of 1
Download datasheet (95Kb)

EMV 1200-40

EMV 1200-40 is an easy to mount LCD digital panel meter.

it is measuring. Only valid readings are displayed; the module indicates "LO" at voltages below 4V and "HI" at voltages above 40V.

only drill a single 5.5mm /

provided. The module's connecting wires pass through the hollow stud into the target application for connection.

protection for the unit when fitted to the meter during installation.

SAFETY

To comply with the Low Voltage Directive (LVD 93/68/EEC), input voltages to the module’s wires must not exceed 60Vd.c. The user must ensure that the

incorporation of the meter into the user’s equipment conforms to the relevant sections of BS EN 61010 (Safety Requirements for Electrical Equipment for

Measuring, Control and Laboratory Use).

APPLICATION

DIMENSIONS

10.5

(0.41)

10.5

(0.41)

Single Hole Mounting

2-Wire Operation

4 to 40

12.5mm / 0.5" LCD Digit Height

Reverse Polarity Protection

Splashproof

V d.c. Full Scale Reading

Module thickness: 5.5mm (0.22")

REAR VIEW

22.0 (0.87)

CAL

44.0 (1.73)

All dimensions in mm (inches)

hole in the panel. The module is fitted to the panel by locating its threaded stud through the hole, fitting the washer and tightening the nut

RED

BLACK

22.0 (0.87)

+4 to +40V d.c.

5.00

(0.20)

The module features a 4 to 40V measurement range with 200mV resolution and is powered from the signal

FITTING THE EMV 1200-40

Drill a 5.5mm /

panel by passing its screw threaded stud and the wires through the hole, fitting the washer

and tightening the nut provided. Take care not to trap either of the connecting wires. Do

not to over tighten the nut as this may damage the meter.

before display switches off.

Reading when Vin > 40V.

Reading when Vin < 4V,

* At voltages below 4.0V d.c., the LCD will display

Easy Mounting Voltmeter

Specification

Accuracy (overall error)

Linearity

Valid displayed reading*

Resolution

Sample rate

Operating temperature range

Supply voltage

Supply current

At Voltages in excess of 40.0V d.c., the LCD will display .

Do NOT exceed 50V d.c., as this may damage the meter.

The module includes reverse polarity protection up to 30V for up to 30 seconds.

Operation and accuracy at voltages above 40.0V or below 4.0V are not specified.

" hole in the panel.

EMV 1200-40

Single Hole Mounting 2-Wire Meter

Fit seal to the rear of the module. Fit the module to the

Seal

Min.

4.0

A rubber seal is included, providing splash proof

(0.35)

9.0

and will ultimately go blank.

Typ.

200

0.4

Panel

To install the meter, the user need

Washer

Max.

40.0

±1

Nut

2 wires - 30cm (12.0)

Shown Actual Size

Stock Number

EMV 1200-40

V (±1 count)

sample/sec

mV d.c.

count

V d.c.

Unit

°C

Related parts for EMV 1200-40

Related keywords

EMV 1200-40 datasheet
EMV 1200-40 data sheet
EMV 1200-40 pdf datasheet
EMV 1200-40 component
EMV 1200-40 part
EMV 1200-40 distributor
EMV 1200-40 RoHS
EMV 1200-40 datasheet download