DP83932CVF-33 National Semiconductor, DP83932CVF-33 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DP83932CVF-33
Manufacturer Part Number
DP83932CVF-33
Description
IC CTRLR ORIENT NETWORK 132PQFP
Manufacturer
National Semiconductor
Series
SONIC™r
Datasheet
1.DP83932CVF-20.pdf
(98 pages)
Specifications of DP83932CVF-33
Controller Type
Ethernet Network Interface Controller
Interface
Bus
Voltage - Supply
5V
Mounting Type
Surface Mount
Package / Case
132-MQFP, 132-PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Supply
-
Operating Temperature
-
Other names
*DP83932CVF-33
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DP83932CVF-33
Manufacturer:
COTO
Quantity:
2 000
Part Number:
DP83932CVF-33
Manufacturer:
NS/国半
Quantity:
20 000
1 0 Functional Description
During transmission of a packet from the SONIC the exter-
nal transceiver will always loop the packet back to the
SONIC The SONIC will use this to monitor the packet as it
is being transmitted The CRC and source address of the
looped back packet are checked with the CRC and source
address that were transmitted If they do not match an error
bit is set in the status of the transmitted packet (see Packet
Monitored Bad PMB in the Transmit Control Register Sec-
tion 4 3 4) Data is not written to the receive FIFO during this
monitoring process unless Transceiver Loopback mode has
been selected (see Section 1 7)
Receive Logic The receive logic contains the command
control and status registers that govern the operations of
the receive section It generates the control signals for writ-
ing data to the receive FIFO processes error signals ob-
tained from the CRC checker and the deserializer activates
the ‘‘packet reject’’ signal to the RSM for rejecting packets
and posts the applicable status in the Receive Control regis-
ter
Deserializer This section deserializes the serial input data
stream and furnishes a byte clock for the address compara-
tor and receive logic It also synchronizes the CRC checker
to begin operation (after SFD is detected) and checks for
proper frame alignment with respect to CRS going inactive
at the end of reception
Address Comparator The address comparator latches the
Destination Address (during reception or loopback) or
Source Address (during transmission) and determines
whether the address matches one of the entries in the CAM
(Content Addressable Memory)
CRC Checker The CRC checker calculates the 4-byte
Frame Check Sequence (FCS) field from the incoming data
stream and compares it with the last 4-bytes of the received
packet The CRC checker is active for both normal recep-
tion and self-reception during transmission
Content Addressable Memory (CAM) The CAM contains
16 user programmable entries and 1 pre-programmed
Broadcast address entry for complete filtering of received
packets The CAM can be loaded with any combination of
Physical and Multicast Addresses (Section 2 2) See Sec-
tion 4 1 for the procedure on loading the CAM registers
1 2 2 MAC Transmit Section
The transmit section (Figure 1-4 ) is responsible for reading
data from the transmit FIFO and transmitting a serial data
(Continued)
FIGURE 1-4 MAC Transmitter
6
Truncated Binary Exponential Backoff Algorithm before
stream onto the network in conformance with the IEEE
802 3 CSMA CD standard The Transmit Section consists
of the following blocks
Transmit State Machine (TSM) The TSM controls the
functions of the serializer preamble generator and JAM
generator It determines the proper sequence of events that
the transmitter follows under various network conditions If
no collision occurs the transmitter prefixes a 7 byte pream-
ble and 1 byte Start of Frame Delimiter (SFD) consisting of a
‘‘10101011’’ sequence at the beginning of each packet
then sends the serialized data At the end of the packet an
optional 4-byte CRC pattern is appended If a collision oc-
curs the transmitter switches from transmitting data to
sending a 4-byte Jam pattern to notify all nodes that a colli-
sion has occurred Should the collision occur during the pre-
amble the transmitter waits for it to complete before jam-
ming After the transmission has completed the transmitter
writes status in the Transmit Control register (Section 4 3 4)
Protocol State Machine The protocol state machine as-
sures that the SONIC obeys the CSMA CD protocol Before
transmitting this state machine monitors the carrier sense
and collision signals for network activity If another node(s)
is currently transmitting the SONIC defers until the network
is quiet then transmits after its Interframe Gap Timer
(9 6 s) has expired The Interframe Gap time is divided into
two portions During the first 6 4 s network activity restarts
the Interframe Gap timer Beyond this time however net-
work activity is ignored and the state machine waits the re-
maining 3 2
ences a collision during a transmission the SONIC switches
from transmitting data to a 4-byte JAM pattern (4 bytes of all
1’s) before ceasing to transmit The SONIC then waits a
random number of slot times (51 2
reattempting another transmission In this algorithm the
number of slot times to delay before the nth retransmission
is chosen to be a random integer r in the range of
If a collision occurs on the 16th transmit attempt the SONIC
aborts transmitting the packet and reports an ‘‘Excessive
Collisions’’ error in the Transmit Control register
s before transmitting If the SONIC experi-
where k
0
s
e
r
s
min(n 10)
2
k
s) determined by the
TL F 10492 – 5