MAX8725ETI Maxim Integrated Products, MAX8725ETI Datasheet - Page 25

• Manufacturer Part Number: MAX8725ETI
• Description: Battery Management Multichemistry Battery Charger
• Manufacturer: Maxim Integrated Products

Specifications of MAX8725ETI

• Product: Charge Management
• Battery Type: Li-Ion, Li-Polymer, NiCd, NiMH, Lead Acid, Universal
• Operating Supply Voltage: 8 V to 28 V
• Supply Current: 2.7 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: TQFN-28
• Charge Safety Timers: No
• Mounting Style: SMD/SMT
• Temperature Monitoring: No
• Uvlo Start Threshold: 9.18 V
• Uvlo Stop Threshold: 9.42 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The loop transfer function is given by:
Since:
the loop transfer function simplifies to:
The crossover frequency is given by:
For stability, choose a crossover frequency lower than
1/10th the switching frequency:
Choosing a crossover frequency of 30kHz and using
the component values listed in Figure 1 yields C
5.4nF. Values for C
mum value may slow down the input current-loop
response excessively. Figure 10 shows the Bode plot of
the input current-limit loop frequency response using
the values calculated above.
Multichemistry Battery Chargers with Automatic
Figure 10. CCS Loop Response
LTF GM
=
100
-20
-40
80
60
40
20
0
IN
0.1
LTF GMS
×
C
A
CS
=
CSS
______________________________________________________________________________________
GM
f
CO CS
= GMS / (2π f
CS
10
IN
×
_
FREQUENCY (Hz)
RS
greater than 10 times the mini-
1
=
+
1
A
=
sR
×
1k
CSS
2π
GMS
R
GMS
OGMS
OGMS
C
1
×
CS
CO_CS
RS
1
100k
+
×
1
sR
MAG
PHASE
C
R
CS
OGMS
)
OGMS
10M
0
-45
-90
×
C
CS
CS
>
System Power Selector
The DHI and DLO outputs are optimized for driving
moderately-sized power MOSFETs. The MOSFET drive
capability is the same for both the low-side and high-
side switches. This is consistent with the variable duty
factor that occurs in the notebook computer environ-
ment where the battery voltage changes over a wide
range. An adaptive dead-time circuit monitors the DLO
output and prevents the high-side FET from turning on
until DLO is fully off. There must be a low-resistance,
low-inductance path from the DLO driver to the
MOSFET gate for the adaptive dead-time circuit to work
properly. Otherwise, the sense circuitry in the
MAX1909/MAX8725 interpret the MOSFET gate as “off”
while there is still charge left on the gate. Use very
short, wide traces measuring 1.25mm to 2.5mm if the
MOSFET is 25mm from the device. Unlike the DLO out-
put, the DHI output uses a fixed-delay 50ns time to pre-
vent the low-side FET from turning on until DHI is fully
off. The same layout considerations should be used for
routing the DHI signal to the high-side FET.
Since the transition time for a p-channel switch can be
much longer than an n-channel switch, the dead time
prior to the high-side PMOS turning on is more pro-
nounced than in other synchronous step-down regula-
tors, which use high-side n-channel switches. On the
high-to-low transition, the voltage on the inductor’s
“switched” terminal flies below ground until the low-side
switch turns on. A similar dead-time spike occurs on
the opposite low-to-high transition. Depending upon the
magnitude of the load current, these spikes usually
have a minor impact on efficiency.
The high-side driver (DHI) swings from SRC to 5V
below SRC and typically sources 0.9A and sinks 0.5A
from the gate of the p-channel FET. The internal pull-
high transistors that drive DHI high are robust, with a
2.0Ω (typ) on-resistance.
The low-side driver (DLO) swings from DLOV to ground
and typically sources 0.5A and sinks 0.9A from the gate
of the n-channel FET. The internal pulldown transistors
that drive DLO low are robust, with a 1.0Ω (typ) on-
resistance. This helps prevent DLO from being pulled
up when the high-side switch turns on, due to capaci-
tive coupling from the drain to the gate of the low-side
MOSFET. This places some restrictions on the FETs
that can be used. Using a low-side FET with smaller
gate-to-drain capacitance can prevent these problems.
MOSFET Drivers
25