Z16C3220VSC Zilog, Z16C3220VSC Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/7/729/zilog_sml.jpg)
Z16C3220VSC
Manufacturer Part Number
Z16C3220VSC
Description
IC Z16C32 MCU 20MHZ IUSC 68PLCC
Manufacturer
Zilog
Series
IUSC™r
Specifications of Z16C3220VSC
Controller Type
USC Controller
Interface
DMA
Voltage - Supply
4.5 V ~ 5.5 V
Current - Supply
7mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
68-LCC (J-Lead)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
Z16C3220VSC
Manufacturer:
ZILOG
Quantity:
5 510
Part Number:
Z16C3220VSC
Manufacturer:
ZILOG
Quantity:
20 000
PIN DESCRIPTION (Continued)
/BUSREQ Bus Request (output, active Low). The DMA
controller section drives this line Low to request control of
the host bus. /BUSREQ can be an open-drain or totem-
pole output depending on a bit in the Bus Configuration
Register. In open-drain mode the IUSC samples the pin as
an input and only drives it Low after sampling it high.
/BIN Bus Acknowledge In (input, active Low). When the
IUSC receives a falling edge on this input, it samples
whether it has been driving (or has just begun to drive)
/BUSREQ. If so, it keeps /BOUT High and takes control of
the host bus. If not, it passes the bus grant by driving
/BOUT Low. This signal can be used with /BOUT to form a
bus-grant daisy chain for arbitration of bus control. Alter-
natively, it can be connected to a direct, positive grant from
an external arbiter, and the /BOUT pin can be left uncon-
nected.
/BOUT Bus Acknowledge Out (output, active Low). As
noted above, this signal can be used with /BIN to form a
bus-grant daisy chain for arbitration of bus control.
/ABORT Abort Master Cycle (input, active Low ). A Low on
this line during a master cycle makes the currently active
DMA channel terminate its activity and enter a disabled
state. Note that /ABORT is only effective during a DMA
cycle, so that the IUSC knows which channel should be
aborted. Also note that external logic must set /WAIT//RDY
to the right state for the cycle to complete, before /ABORT
becomes effective.
RxD Received Data (input, positive logic). The serial input.
TxD Transmit Data (output, positive logic). The serial
output.
/RxC Receive Clock (input or output). This signal can be
used as a clock input for any of the functional blocks in the
serial controller. Or, software can program the IUSC so that
this pin is an output carrying any of several receiver or
internal clock signals, a general-purpose input or output,
or an interrupt input.
9
Z
ILOG
P R E L I M I N A R Y
/TxC Transmit Clock (input or output). This signal can be
used as a clock input for any of the functional blocks in the
serial controller. Or, software can program the IUSC so that
this pin is an output carrying any of several transmitter or
internal clock signals, a general purpose input or output, or
an interrupt input.
/RxREQ Receive DMA Request (input or output). In device
testing or in applications not using the serial controller and
DMA controller sections together in the usual way, this pin
can carry an active Low DMA Request from the receive
FIFO. On the IUSC this request is internally routed to the
on-chip Receive DMA channel; it is more typical to use the
RxREQ pin as a general-purpose output or as an interrupt
input.
/TxREQ Transmit DMA Request (input or output). In device
testing or in applications not using the serial controller and
DMA controller sections together in the usual way, this pin
can carry an active Low DMA Request from the transmit
FIFO. On the IUSC this request is internally routed to the
on-chip Transmit DMA channel, and it’s more typical to use
the RxREQ pin as a general-purpose output or as an
interrupt input.
/DCD Data Carrier Detect (input or output, active Low).
Software can program the IUSC so that this signal enables/
disables the receiver. In addition, software can program
the device to request interrupts in response to transitions
on this line. The pin can also be used as a simple input or
output.
/CTS Clear to Send (input or output, active Low). Software
can program the IUSC so that this signal enables/disables
the transmitter. In addition, software can program the
device to request interrupts in response to transitions on
this line. The pin can also be used as a simple input or
output.
PS97USC0200
Z16C32 IUSC
™