MCP2140T-I/SS Microchip Technology, MCP2140T-I/SS Datasheet - Page 16
![IC IRDA CONTROLLR DTE/DCE 20SSOP](/photos/6/58/65895/150-20-ssop_sml.jpg)
MCP2140T-I/SS
Manufacturer Part Number
MCP2140T-I/SS
Description
IC IRDA CONTROLLR DTE/DCE 20SSOP
Manufacturer
Microchip Technology
Specifications of MCP2140T-I/SS
Package / Case
20-SSOP
Controller Type
IRDA Standard Protocol Stack Controller
Interface
UART
Voltage - Supply
3 V ~ 5.5 V
Current - Supply
2.2mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP2140DM-TMPSNS - BOARD DEMO FOR MCP2140
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP2140T-I/SS
Manufacturer:
BOURNS
Quantity:
12 000
Part Number:
MCP2140T-I/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MCP2140
2.10.1
Actual maximum throughput is dependent on several
factors, including:
• Characteristics of the Primary device
• Characteristics of the MCP2140
• IrDA standard protocol overhead
The IrDA standard specifies how the data is passed
between the Primary device and Secondary device. In
IrCOMM, an additional 8 bytes are used by the protocol
for each packet transfer.
The most significant factor in data throughput is how
well the data frames are filled. If only 1 byte is sent at a
time, the throughput overhead of the IrCOMM protocol
is 89% (see
throughput is to align the amounts of data with the
receive buffer (IR and Host UART) packet size of the
MCP2140.
Then there is the delay between when data packets
are sent and received. See
of this delay (look at CTS signal falling edges). In this
screen capture, a Palm™ m105 is receiving a 240-
byte string of data from the MCP2140. When the CTS
signal goes high, the Host Controller stops sending
data (23 bytes per CTS low-time). The CTS falling
edge to CTS falling edge is approximately 90 ms (typ-
ical). This CTS high-time affects the total data through-
put. The CTS high-time will be dependant on the
characteristics of the Primary device.
TABLE 2-5:
DS21790A-page 16
MCP2140
Receive
Receive
UART
Note 1: Overhead % =
Host
IR
2: The maximum number of bytes of the IR
3: The maximum number of bytes of the
4: The CTS signal is driven high at 23 byte.
IMPROVING THROUGHPUT
(Bytes)
Packet
Receive buffer.
Host UART Receive buffer.
Size
Data
Table
64
29
23
1
1
IRCOMM OVERHEAD %
Overhead/(Overhead + Data).
2-5). The best way to maximize
Overhead
IrCOMM
(Bytes)
8
8
8
8
8
Figure 2-10
Overhead
IrCOMM
89 %
22 %
26 %
89 %
%
11 %
(1)
for an example
Comment
Note 2
Note 3
Note 4
Preliminary
2.10.1.1
The MCP2140 uses a fixed IR Receiver data block size
of 64 bytes.
The minimum size frame the Primary device can
respond with is 6 bytes.
2.10.1.2
The MCP2140 uses a fixed Host UART Receiver data
block size of 29 bytes.
2.11
An IR link can be compared to a one-wire data connec-
tion. The IR transceiver can transmit or receive, but not
both at the same time. A delay of one bit time is recom-
mended between the time a byte is received and
another byte is transmitted.
2.12
The MCP2140 has a fixed Device ID. This Device ID is
“MCP2140 xx”, with the xx indicating the silicon
revision of the device.
Turnaround Latency
Device ID
From the Primary Device
From the MCP2140
2003 Microchip Technology Inc.