USB2517I-JZX SMSC, USB2517I-JZX Datasheet - Page 24

• Manufacturer Part Number: USB2517I-JZX
• Description: IC CTRLR USB2.0 7PORT 64QFN
• Manufacturer: SMSC
• Type: USB HUB Controllerr

Specifications of USB2517I-JZX

• Controller Type: USB 2.0 Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 130mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-QFN
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current: 120 mA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1090

Revision 1.1 (04-26-10)
LED_B_N[2:1] /
PRTPWR_POL
BOOST[1:0]
OCS_N[x:1]
SYMBOL
RBIAS
BUFFER
TYPE
I/O12
IPU
IPU
I-R
DOWNSTREAM USB 2.0 INTERFACES (continued)
Table 5.2 USB251x Pin Descriptions (continued)
Enhanced Indicator Port LED for ports 1 and 2
Enhanced indicator LED for ports 1 and 2. This pin will be active low when
LED support is enabled via EEPROM or SMBus.
If this strap option is enabled by package and configuration settings (see
Table 8.1, "Hub Configuration
negation to determine if all PHY ports (upstream and downstream) operate at
a normal or boosted electrical level. Also, the active state of the LEDs will be
determined as follows:
See
8.2.1.29, "Register F8h: Boost_4:0," on page 46
BOOST[1:0] = BOOST_IOUT[1:0]
BOOST[1:0] = ‘00’,
LED_B_N[2] is active high,
LED_B_N[1] is active high.
BOOST[1:0] = ‘01’,
LED_B_N[2] is active high,
LED_B_N[1] is active low.
BOOST[1:0] = ‘10’,
LED_B_N[2] is active low,
LED_B_N[1] is active high.
BOOST[1:0] = ‘11’,
LED_B_N[2] is active low,
LED_B_N[1] is active low.
Port Power Polarity Strapping
Port Power Polarity strapping determination for the active signal polarity of
the [x:1]PRTPWR pins.
While RESET_N is asserted, the logic state of this pin will (through the use
of internal combinatorial logic) determine the active state of the PRTPWR
pins in order to ensure that downstream port power is not inadvertently
enabled to inactive ports during a hardware reset.
When RESET_N is negated, the logic value will be latched internally, and will
retain the active signal polarity for the PRTPWR[x:1] pins.
‘1’ = PRTPWR[x:1]_P/N pins have an active ‘high’ polarity
‘0’ = PRTPWR[x:1]_P/N pins have an active ‘low’ polarity
Warning: Active low port power controllers may glitch the downstream port
power when the system power is first applied. Care should be taken when
designing with active low components.
When PRTPWR_POL is not an available pin on the package, the hub will only
support active high power controllers.
Over-Current Sense
Input from external current monitor indicating an over-current condition.
USB Transceiver Bias
A 12.0 k
transceiver’s internal bias settings.
Section 8.2.1.27, "Register F6h: Boost_Up," on page 45
Ω
(+/- 1%) resistor is attached from ground to this pin to set the
DATASHEET
24
Options"), this pin will be sampled at RESET_N
DESCRIPTION
for more information.
USB 2.0 Hi-Speed Hub Controller
and
SMSC USB251x
Section
Datasheet