USB2504A-JT SMSC, USB2504A-JT Datasheet - Page 39

• Manufacturer Part Number: USB2504A-JT
• Description: IC HUB 4PORT USB COMPATBL 64TQFP
• Manufacturer: SMSC
• Type: Integrated USB Compatibler

Specifications of USB2504A-JT

• Controller Type: USB Hub
• Interface: I²C
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 100mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Digital Ic Case Style: TQFP
• No. Of Pins: 64
• Operating Temperature Range: 0°C To +70°C
• Data Rate Max: 480Mbps
• Supply Current: 295mA
• Supply Voltage Max: 3.6V
• Rohs Compliant: Yes
• For Use With: 638-1038 - BOARD EVALUATION FOR USB2504
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1031

Integrated USB 2.0 Compatible 4-Port Hub
Datasheet
Chapter 6 Backward Compatibility to the USB20H04
SMSC USB2504/USB2504A
6.1
6.2
6.3
6.4
Internal 1.8V regulator
Configuration by Internal Defaults
Configuration by SMBus
PRTPWR_POL
The USB2504/USB2504A is pin compatible to the USB20H04, but is not designed to be a direct drop-
in replacement. Many existing USB20H04 designs may accommodate a USB2504/USB2504A in place
of the USB20H04, as long as specific Bill-Of-Material (BOM) modifications and population option
changes are implemented. Since each design is unique, every customer considering a change from a
USB20H04 to a USB2504/USB2504A should contact SMSC Applications Engineering for assistance.
The USB2504/USB2504A has two internal 1.8V regulators that are enabled by default (ATEST pin
contains an internal pull-up, and was specified as a No-Connect in the USB20H04 datasheet). Each
regulator requires a separate 4.7uF Low ESR capacitor to ground. The USB20H04 designs that directly
connect the Digital and Analog 1.8V pins together will not support a USB2504/USB2504A (unless the
internal regulators are disabled).
The internal default settings that are loaded when this option is selected are very similar (but not
identical) to those that were loaded in the USB20H04. The CFG_SEL[2:0] pins will properly select this
method if the existing USB20H04 design was set-up to load the configuration via internal defaults.
The USB2504/USB2504A has pin strapping options that enable modification of the internal default load
without requiring an EEPROM. The CFG_SEL2 pin (pin 59) on the USB2504/USB2504A was a VSS
pin on the USB20H04 so this functionality will be disabled when a USB2504/USB2504A is placed into
a USB20H04 design.
The CFG_SEL[2:0] pins will properly select this method if the existing USB20H04 design was set-up
to load the configuration via SMBus. The USB2504/USB2504A has a few additional registers, and has
also moved some of the configuration bits so the actual SMBus code load itself will need to be
modified. If a USB20H04 SMBus load is programmed into a USB2504/USB2504A, the results are
unpredictable.
The USB2504/USB2504A has a new strapping option that enables the port power control active state
to be either active-high or active-low. The USB20H04 only provided active-low port power control. The
PRTPWR_POL pin on the USB2504/USB2504A is pin 23, which was a VSS pin on the USB20H04,
so by default, a USB20H04 design will select active-low port port control.
DATASHEET
39
Revision 2.3 (08-27-07)