TP3070V-XD National Semiconductor, TP3070V-XD Datasheet
TP3070V-XD
Specifications of TP3070V-XD
Available stocks
Related parts for TP3070V-XD
TP3070V-XD Summary of contents
Page 1
... Standard serial control interface operating power (typ) n 1.5 mW standby power (typ) n Designed for CCITT and LSSGR applications n TTL and CMOS compatible digital interfaces n Extended temperature versions available for −40˚C to +85˚C (TP3070V-X) Note: See also AN-614, COMBO II application guide. April 1994 www.national.com ...
Page 2
... Block Diagram Connection Diagrams Order Number TP3070V (0˚C to +70˚C) Order Number TP3070V-X (−40˚C to +85˚C) See NS Package Number V28A www.national.com FIGURE 1. See NS Package Number J20A DS008635-4 See NS Package Number N20A Pin Descriptions Pin ± V +5V CC ± V −5V BB GND Ground. All analog and digital signals are referenced to this pin ...
Page 3
Pin Descriptions (Continued) Pin Description FS Receive Frame Sync input. Normally a pulse R or squarewave with an 8 kHz repetition rate is applied to this input to define the start of the receive time slot assigned to this device ...
Page 4
Functional Description POWER-DOWN STATE Following a period of activity in the powered-up state the power-down state may be re-entered by writing any of the control instructions into the serial control port with the “P” bit set to “1” as indicated ...
Page 5
Functional Description (Continued) TABLE 1. Programmable Register Instructions Function Single Byte Power-Up/Down Write Control Register Read-Back Control Register Write to Interface Latch Register Read Interface Latch Register Write Latch Direction Register Read Latch Direction Register Write Receive Gain Register Read ...
Page 6
Programmable Functions vice is powered-up or down by setting the “P” bit as indi- cated. When the power-up or down control is entered as a single byte instruction, bit one (1) must be reset When a power-up ...
Page 7
Programmable Functions µ255 law MSB = +Full Scale −Full ...
Page 8
Programmable Functions and convert to the binary equivalent. Some examples are given in Table 7 and a complete tabulation is given in Appen- dix I of AN-614. It should be noted that the Transmit (idle channel) Noise and Transmit Signal ...
Page 9
Programmable Functions FIGURE 2. Simplified Diagram of Hybrid Balance Circuit Three registers must be programmed in COMBO II to fully configure the Hybrid Balance Filter as follows: Register 1: select/de-select Hybrid Balance Filter; invert/non-invert cancellation signal; select/de-select Hybal2 filter section; ...
Page 10
Applications Information FIGURE 3. Typical Application with Monolithic SLIC www.national.com (Continued) 10 DS008635-7 ...
Page 11
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications GND CC Voltage 0. Voltage at any Digital Input V + 0.5V to GND − 0.5V CC Electrical Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚ ...
Page 12
Electrical Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing at T correlation with other production tests and/or product design and characterization. All signals ...
Page 13
Timing Specifications (Continued) Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing at T correlation with other production tests and/or product design and characterization. All ...
Page 14
Timing Specifications (Continued) Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing at T correlation with other production tests and/or product design and characterization. All ...
Page 15
Timing Diagrams (Continued) FIGURE 5. Delayed Data Timing Mode (Time Slot Zero Only) 15 DS008635-9 www.national.com ...
Page 16
Timing Diagrams (Continued) www.national.com 16 ...
Page 17
Transmission Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing dBm0 PCM code. Transmit and receive gains programmed for ...
Page 18
Transmission Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing dBm0 PCM code. Transmit and receive gains programmed for ...
Page 19
Transmission Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing dBm0 PCM code. Transmit and receive gains programmed for ...
Page 20
Transmission Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing dBm0 PCM code. Transmit and receive gains programmed for ...
Page 21
Transmission Characteristics Unless otherwise noted, limits printed in BOLD characters are guaranteed for V +70˚C (−40˚C to +85˚C for TP3070-X) by correlation with 100% electrical testing dBm0 PCM code. Transmit and receive gains programmed for ...
Page 22
Definitions and Timing Conventions DEFINITIONS the D.C. input level above which input level is guaranteed to appear as a logical one. This parameter measured by performing a functional test at reduced ...
Page 23
23 ...
Page 24
Physical Dimensions inches (millimeters) unless otherwise noted www.national.com Ceramic Dual-In-Line Package (J) Order Number TP3071J NS Package Number J20A Ceramic Dual-In-Line Package (J) Order Number TP3070J NS Package Number J28A 24 ...
Page 25
Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package (N) Order Number TP3071N NS Package Number N20A 25 www.national.com ...
Page 26
... National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. Plastic Leaded Chip Carrier (V) Order Number TP3070V or TP3070V-X NS Package Number V28A 2 ...