MAX1098CEAE+ Maxim Integrated Products, MAX1098CEAE+ Datasheet - Page 14

• Manufacturer Part Number: MAX1098CEAE+
• Description: Board Mount Temperature Sensors 10Bit SerialOut Temp Sensor w/5Ch ADC
• Manufacturer: Maxim Integrated Products

Specifications of MAX1098CEAE+

• Full Temp Accuracy: +/- 4 C
• Package / Case: SSOP-16
• Digital Output - Bus Interface: Serial (3-Wire)
• Digital Output - Number Of Bits: 10 bit
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Output Type: Digital
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Input data (configuration and conversion bytes) are
clocked into the MAX1098/MAX1099 at DIN on the ris-
ing edge of SCLK when CS is low. The start bit (MSB)
of an input data byte is the first logic 1 bit that arrives:
After CS falls
After receipt of a complete configuration byte with no
conversion in progress
After 16 bits have been clocked onto DOUT following a
conversion.
10-Bit Serial-Output Temperature Sensors
with 5-Channel ADC
Figure 4. Detailed Serial Interface Timing
Figure 5. Bipolar Transfer Function
14
______________________________________________________________________________________
0111111111
0111111110
0000000010
0000000001
0000000000
1111111111
1111111110
1111111101
1000000010
1000000001
OUTPUT CODE
- FS + 1LSB
DOUT
SCLK
+ FS = + 2V
- FS = - 2V
1LSB = 2V
DIN
CS
512
REF
REF
REF
t
OR
OR
CS0
X
IN + - IN - (LSB)
t
DS
0
t
t
DV
CSS
VALID
Input Data Format
+ FS - 1LSB
t
CH
t
DH
X
t
CL
t
VALID
DO
Output data from the MAX1098/MAX1099 are clocked
onto DOUT on the falling edge of SCLK in the form of two
8-bit words, MSB first (Table 5). For temperature conver-
sions, the output is 12-bit binary (D8–S2) padded with 2
leading extraneous bits and two trailing zeros. For volt-
age conversions, the output is 10-bit two’s-complement
binary (D9–D0) with 3 sub-bits and two trailing zeros.
Figure 5 shows the bipolar transfer function.
On power-up, the MAX1098/MAX1099 default to shut-
down mode. Start a conversion by transferring a configu-
ration byte and a conversion byte into DIN with the
control formats shown in Tables 1 and 2, respectively.
(See Power Modes for a related discussion.)
SSTRB goes low on the falling edge of the last bit of the
conversion byte, and it returns high when the conversion
is complete. For best noise performance, SCLK should
remain low while SSTRB is low. Typical conversion times
are 2.2ms for temperature measurements and 1.1ms for
voltage measurements. The MSB of the 2 output bytes is
present at DOUT starting at the rising edge of SSTRB.
Successive SCLK falling edges shift the two 8-bit data
bytes out from an internal register. Additional (>16)
SCLK edges will result in zeros on DOUT.
SSTRB does not go into a high-impedance state when
CS goes high. Pulling CS high prevents data from
being clocked in or out, but it does not adversely affect
a conversion in progress. Figure 6 shows SSTRB timing
details.
Subsequent conversions with the same reference mode
do not require a configuration byte.
VALID
t
CSH
Performing a Conversion
X
t
CS
t
CS1
t
TR
Output Data Format