ATF22V10CQZ-20XI Atmel, ATF22V10CQZ-20XI Datasheet
![IC PLD 20NS POWER 24TSSOP](/photos/6/71/67110/313-24-tssop_sml.jpg)
ATF22V10CQZ-20XI
Specifications of ATF22V10CQZ-20XI
Related parts for ATF22V10CQZ-20XI
ATF22V10CQZ-20XI Summary of contents
Page 1
... PLDs. Ten outputs are each allocated product terms. Three different modes of opera- tion, configured automatically with software, allow highly complex logic functions to be realized. High-performance Electrically Erasable Programmable Logic Device Atmel ATF22V10CZ Atmel ATF22V10CQZ 0778L–PLD–8/10 ...
Page 2
... GND 12 Figure 2-3. PLCC GND Note: For PLCC, P1, P8, P15 and P22 can be left unconnected. For superior perfor- mance, connect VCC to pin 1 and GND to 8, 15, and 22 Atmel ATF22V10C(Q)Z 2 Figure 2-2. DIP/SOIC CLK/IN 24 VCC 23 I/O 22 I/O 21 I/O 20 I/O 19 I/O 18 I/O 17 I/O 16 I/O ...
Page 3
... V = MAX IN CQZ-20 Com Outputs Open CQZ-20 Ind V = 0.5V OUT Min 16mA Min, CCIO I = -4.0mA OH Atmel ATF22V10C(Q)Z + 0.75V DC, which may overshoot to 7.0V for CC Industrial -40⋅C - 85⋅C 5V ± 10% Min Typ Max - 150 90 180 100 5 120 5 100 5 120 -130 -0.5 0.8 2 0.75 CC 0.5 2.4 Units µ ...
Page 4
... AP Register t Setup Time, Synchronous Preset SP t Asynchronous Reset Width AW t Asynchronous Reset Recovery Time AR Synchronous Preset to Clock Recovery t SPR Time Note: 1. See ordering information for valid part numbers Atmel ATF22V10C(Q tAW tAR tCO tAP tER VALID VALID tPD tER VALID VALID ...
Page 5
... Output Test Loads Note: Similar competitors devices are specified with slightly different loads. These load differences may affect output signals’ delay and slew rate. Atmel devices are tested with sufficient margins to meet compatible device specification conditions. 4.5 Pin Capacitance Table 4-1 ...
Page 6
... These bits can be used for user-specific data. 6. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the Atmel programmed, fuse verify and preload are inhibited. However, the 64-bit User Signature remains accessible. The security fuse should be programmed last, as its effect is immediate. ...
Page 7
... These are relatively weak active circuits that can be easily overridden by TTL-compatible drivers (see input and I/O diagrams below). Figure 8-1. Input Diagram INPUT PROTECTION CIRCUIT Figure 8-2. I/O Diagram INPUT 0778L–PLD–8/ 100K ESD 100K Atmel ATF22V10C(Q)Z I/O 7 ...
Page 8
... P22V10LCC 10. Functional Logic Diagram Description The Functional Logic Diagram describes the Atmel The ATF22V10CZ/CQZ has 12 inputs and 10 I/O macrocells. Each macrocell can be configured into one of four output configurations: active high/low, registered/combinatorial output.The universal architecture of the ATF22V10CZ/CQZ can be programmed to emulate most 24-pin PAL devices. ...
Page 9
... Figure 10-1. Functional Logic Diagram 0778L–PLD–8/10 Atmel ATF22V10C(Q)Z 9 ...
Page 10
... OL 140.0 120.0 100.0 80.0 60.0 40.0 20.0 5.5 6.0 NORMALIZED ICC VS. TEMP -40.0 0.0 25.0 TEMPERATURE (C) ATMEL ATF22V10CQZ SUPPLY CURRENT VS. INPUT FREQUENCY ( 0.000 0.0 0.5 2.5 5.0 7.5 10.0 FREQUENCY (MHz) ATMEL ATF22V10CZ/CQZ OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE (V CC 0.0 ...
Page 11
... ATMEL ATF22V10CZ/CQZ INPUT CLAMP CURRENT VS INPUT VOLTAGE (V 0 -20 -40 -60 -80 -100 -120 0.0 -0.2 -0.4 INPUT VOLTAGE (V) NORMALIZED T 1.2 1.1 1.0 0.9 0.8 4.5 4.8 5.0 SUPPLY VOLTAGE (V) NORMALIZED T 1.3 1.2 1.1 1.0 0.9 0.8 4.5 4.8 5.0 SUPPLY VOLTAGE (V) NORMALIZED T 1 ...
Page 12
... ATMEL ATF22V10C DELTA T VS. OUTPUT LOADING CO 50 100 150 200 NUMBER OF OUTPUTS LOADING DELTA T vs OUTPUT SWITCHING CO 0.0 1.0 2.0 3.0 4.0 5.0 6 ...
Page 13
... ATF22V10CZ-12JC ATF22V10CZ-12PC 8 ATF22V10CZ-12SC ATF22V10CZ-12XC ATF22V10CZ-15JC ATF22V10CZ-15PC ATF22V10CZ-15SC 8 ATF22V10CZ-15JI ATF22V10CZ-15PI ATF22V10CZ-15SI ATF22V10CQZ-20JC ATF22V10CQZ-20PC ATF22V10CQZ-20SC ATF22V10CQZ-20XC 12 ATF22V10CQZ-20JI ATF22V10CQZ-20PI ATF22V10CQZ-20SI ATF22V10CQZ-20XI t CO (ns) Ordering Code ATF22V10CQZ-20JU ATF22V10CQZ-20PU 12 ATF22V10CQZ-20SU ATF22V10CQZ-20XU Package Type Atmel ATF22V10C(Q)Z Package Operation Range 28J Commercial 24P3 24S (0⋅C to 70⋅C) 24X 28J ...
Page 14
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102mm) maximum. Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22V10C(Q)Z 14 1.14(0.045) X 45° PIN NO. 1 IDENTIFIER E1 E ...
Page 15
... Mold Flash or Protrusion shall not exceed 0.25mm (0.010"). Package Drawing Contact: packagedrawings@atmel.com 0778L–PLD–8/10 D PIN TITLE 24P3, 24-lead (0.300"/7.62mm Wide) Plastic Dual Inline Package (PDIP) Atmel ATF22V10C(Q)Z COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – 5.334 A1 0.381 – – D 31.623 – ...
Page 16
... SOIC PIN 1 ID PIN Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22V10C(Q TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM NOTE A – – 2.65 A1 0.10 – 0.30 D 10.00 – ...
Page 17
... Package Drawing Contact: packagedrawings@atmel.com 0778L–PLD–8/10 0.30(0.012) 0.19(0.007) 4.48(0.176) 4.30(0.169) 0.65(0.0256)BSC 7.90(0.311) 7.70(0.303) 0.15(0.006) 0.05(0.002 0.75(0.030) 0.45(0.018) TITLE 24X, 24-lead (4.4mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) Atmel ATF22V10C(Q)Z 6.50(0.256) 6.25(0.246) 1.20(0.047)MAX 0.20(0.008) 0.09(0.004) 04/11/2001 DRAWING NO. 24X REV ...
Page 18
... For I Industrial grade parts Shade Standard Package Options and add note, “Shaded parts are not recommended for new designs. Customers should transition to ROHS offering” Remove Atmel ATF22V10CZ-15XC and Atmel ATF22V10CZ-15XI from Standard Package Options 0778J 11/2005 Add Green Package options ...
Page 19
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...