ATF22LV10CQZ-30XI Atmel, ATF22LV10CQZ-30XI Datasheet
![IC PLD EE 30NS "QZ" PWR 24-TSSOP](/photos/6/71/67110/313-24-tssop_sml.jpg)
ATF22LV10CQZ-30XI
Specifications of ATF22LV10CQZ-30XI
Related parts for ATF22LV10CQZ-30XI
ATF22LV10CQZ-30XI Summary of contents
Page 1
... These additional product terms are common to all ten registers and are automatically cleared upon power-up. Register Preload simplifies testing. A security fuse prevents unauthorized copying of programmed fuse patterns. High-performance Electrically Erasable Programmable Logic Device Atmel ATF22LV10CZ Atmel ATF22LV10CQZ 0779M–PLD–7/10 ...
Page 2
... TSSOP is the smallest package of SPLD offering Figure 2-3. PLCC GND Note: For PLCC, pins 1, 8, 15, and 22 can be left unconnected. For superior perfor- mance, connect VCC to pin 1 and GND to pins 8, 15, and 22 Atmel ATF22LV10C(Q)Z 2 Figure 2-2. CLK/IN 24 VCC 23 I/O 22 I/O 21 I/O 20 I/O 19 I/O 18 I/O 17 I/O 16 I/O 15 ...
Page 3
... Operating Temperature (Ambient) V Power Supply CC 0779M–PLD–7/10 Atmel ATF22LV10C(Q)Z *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond ...
Page 4
... Note: 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec 2. For DC characterization, the test condition Shaded devices are becoming obsolete and replaced with CQZ-30 part in green package offering Atmel ATF22LV10C(Q)Z 4 (2) Condition 0 V ...
Page 5
... Shaded products are becoming obsolete 0779M–PLD–7/ tAW tAR tCO tAP VALID VALID tPD VALID VALID + Atmel ATF22LV10C(Q)Z tER tEA OUTPUT VALID DISABLED tER tEA OUTPUT VALID DISABLED (2) -25 -30 Min Max Min 3.0 25.0 10.0 13.0 10.0 2.0 15.0 4.0 15.0 18 ...
Page 6
... Output Test Loads Note: Similar competitors devices are specified with slightly different loads. These load differences may affect output signals’ delay and slew rate. Atmel devices are tested with sufficient margins to meet compatible device specification conditions 4.5 Pin Capacitance Table 4-1. Pin Capacitance (f = 1MHz 25 ...
Page 7
... These bits can be used for user-specific data. 6. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the Atmel programmed, fuse verify and preload are inhibited. However, the 64-bit User Signature remains accessible. The security fuse should be programmed last, as its effect is immediate. ...
Page 8
... INPUT 9. Functional Logic Diagram Description The Functional Logic Diagram describes the Atmel The ATF22LV10CZ/CQZ has 12 inputs and 10 I/O macrocells. Each macrocell can be configured into one of four output configurations: active high/low or registered/combinatorial. The universal architecture of the ATF22LV10CZ/CQZ can be programmed to emulate most 24-pin PAL devices. ...
Page 9
... Figure 9-1. Functional Logic Diagram Atmel ATF22LV10CZ/CQZ 0779M–PLD–7/10 Atmel ATF22LV10C(Q)Z 9 ...
Page 10
... NORMALIZED I VS. TEMP CC 1.2 1.1 1.0 0.9 0.8 -40.0 0.0 25.0 TEMPERATURE (C) ATMEL ATF22LV10CQZ SUPPLY CURRENT VS. INPUT FREQUENCY (V = 3.3V 5.000 0.000 0.0 0.5 2.5 5.0 7.5 10.0 Frequency (MHz) ATMEL ATF22LV10C/CZ OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE (V = 3.3V ...
Page 11
... ATMEL ATF22LV10CZ/CQZ INPUT CLAMP CURRENT VS. INPUT VOLTAGE (V 20.0 0.0 -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 0.0 -0.2 -0.4 INPUT VOLTAGE (V) NORMALIZED T 1.2 1.1 1.0 0.9 0.8 3.0 3.2 3.3 SUPPLY VOLTAGE (V) NORMALIZED T 1.2 1.1 1.0 0.9 0.8 3.0 3.2 3.3 SUPPLY VOLTAGE (V) NORMALIZED T 1 ...
Page 12
... ATMEL AT22LV10CZ/CQZ DELTA T VS. OUTPUT LOADING CO 0.50 1.00 1.50 2.00 2.50 OUTPUT LOADING (PF) DELTA T VS OUTPUT SWITCHING CO 2.0 3.0 4.0 5.0 6.0 7.0 8 ...
Page 13
... Ordering Code ATF22LV10CZ-25JC ATF22LV10CZ-25PC ATF22LV10CZ-25SC ATF22LV10CZ-25XC ATF22LV10CZ-25JI ATF22LV10CZ-25PI ATF22LV10CZ-25SI ATF22LV10CZ-25XI 15 ATF22LV10CQZ-30JC ATF22LV10CQZ-30PC ATF22LV10CQZ-30SC ATF22LV10CQZ-30XC ATF22LV10CQZ-30JI ATF22LV10CQZ-30PI ATF22LV10CQZ-30SI ATF22LV10CQZ-30XI (ns) Ordering Code ATF22LV10CQZ-30JU ATF22LV10CQZ-30PU 15 ATF22LV10CQZ-30SU ATF22LV10CQZ-30XU Package Type Atmel ATF22LV10C(Q)Z Package Operation Range 28J Commercial 24P3 24S (0C to 70C) 24X 28J ...
Page 14
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102mm) maximum. Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22LV10C(Q)Z 14 1.14(0.045) X 45° PIN NO. 1 IDENTIFIER E1 E ...
Page 15
... Mold Flash or Protrusion shall not exceed 0.25mm (0.010"). Package Drawing Contact: packagedrawings@atmel.com 0779M–PLD–7/10 D PIN TITLE 24P3, 24-lead (0.300"/7.62mm Wide) Plastic Dual Inline Package (PDIP) Atmel ATF22LV10C(Q)Z COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A – – 5.334 A1 0.381 – – D 31.623 – ...
Page 16
... SOIC PIN 1 ID PIN Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22LV10C(Q TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX NOTE SYMBOL A – – 2.65 A1 0.10 – 0.30 D 10.00 – ...
Page 17
... Package Drawing Contact: packagedrawings@atmel.com 0779M–PLD–7/10 0.30(0.012) 0.19(0.007) 4.48(0.176) 4.30(0.169) 0.65(0.0256)BSC 7.90(0.311) 7.70(0.303) 0.15(0.006) 0.05(0.002 0.75(0.030) 0.45(0.018) TITLE 24X, 24-lead (4.4mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) Atmel ATF22LV10C(Q)Z 6.50(0.256) 6.25(0.246) 1.20(0.047)MAX 0.20(0.008) 0.09(0.004) 04/11/2001 DRAWING NO. 24X REV ...
Page 18
... Revision History Doc. Rev. Date Comments M 07/2010 Atmel ATF22LV10CZ-25JC/JI, PC/PI, SC/SI, XC/XJ leaded parts will become obsolete L 11/2005 Added Green Package options Atmel ATF22LV10C(Q)Z 18 0779M–PLD–7/10 ...
Page 19
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...