E32-T61-S 0.3M Omron, E32-T61-S 0.3M Datasheet - Page 64
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
E32-T61-S 0.3M
Manufacturer Part Number
E32-T61-S 0.3M
Description
Fiber Optic Sensors Fiber Cable
Manufacturer
Omron
Datasheet
1.E39-F13.pdf
(67 pages)
Specifications of E32-T61-S 0.3M
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
E32T61S03M
E39-F11 Sleeve Bender
Heat-resistant Fiber Units
E32-T14 and E32-G14
These Units may enter the light-ON
state if there are reflecting objects at
the ends of the lenses. In this case,
attach the black stickers provided to
the ends of the lenses.
Wafer Sensors (E32-L25(A))
E32-T16 and E32-T16P
E32-M21
Separate the 4 fibers by distances sufficient to prevent inter-
ference.
Vacuum-resistant Fiber Units (E32-V)
Although Flanges, Fiber Units on the vacuum side, and Lens
Units have been cleaned, as an extra precaution, clean these
products with alcohol before use in high-vacuum environ-
ments to ensure that they are properly degreased.
Liquid-level Detection Sensors (E32-D82F)
64
90° max.
• The bending radius of the stainless steel tube should be as
• Insert the tip of the stain-
• The fibers of these Units cannot be extended using the E39-
• The maximum allowable temperature for continuous opera-
• To ensure correct performance, insert the fiber with a white
• Secure the Fiber Unit using the unbendable section. Other-
• For applications in hazardous environments, install the Fi-
E32-T16's sensing head
Example
large as possible. The smaller the bending radius becomes,
the shorter the sensing distance will be.
less steel tube to the
Sleeve Bender and bend
the stainless steel tube
slowly along the curve of
the Sleeve Bender.
F10 Fiber Connector.
tion with these Units is 130°C. It is 150°C for short-term use.
line into the emitter-side port of the Amplifier Unit.
wise, the liquid-level detection position may be displaced.
ber Unit in the hazardous environment but install the Ampli-
fier Unit in a safe environment.
(E32-D51 and E32-T51)
10 mm
Slit provided
10 mm
Do not bend here.
To use the slit provided, peel off the
backing sheet, align it with the edg-
es of the sensing surface, and at-
tach it to the sensing head. Use the
slit in applications where saturation
occurs (i.e., changes in light inten-
sity cannot be obtained) due to
short sensing distances.
R7.5 mm
R12.5 mm
1.2 mm dia. max.
1.3 mm dia. min.
Stickers
Stainless
steel tube
R10 mm
Fiber tip
position
mark
R5 mm
Liquid-level Detection Sensors: Tube-mounting Models
E32-A07E1(E2)
There is a difference in sensing
object angle between E32-A07E1
and E32-A07E2. Select a model in
accordance with the bending
direction of a sensing object. Use
the fiber with a model display tube
as light emitting side.
● Adjustment
E32-G14
When a Digital Fiber Amplifier is used, the sensing distance is
short, making the incident light intensity large. This makes it
impossible to teach without a workpiece.
Liquid-level (E32-D82F) Detection Position
The liquid-level detection po-
sition is at a distance of
5.2±2 mm from the end of the
fluororesin section.
(Refer to the diagram on the
right.)
The liquid-level detection po-
sition varies with the surface
tension of the liquid and the degree of wetness at the Fiber
Unit's detection position.
● Other Considerations
Liquid Level (E32-D82F)
Heat-resistant Fiber Units (E32-D81R(-S), E32-D61(-S), and
E32-D73(-S))
The pitch of the emission-side and reception-side fiber-inser-
tion ports varies with the Amplifier Unit. Be sure to use an ap-
propriate Fiber Unit.
Chemical-resistant Fiber and Liquid Level (E32-D82F)
Fluororesin has high chemical resistance. However, applications in
the atmosphere of vaporized chemicals (gases) or steam may cause
malfunction or damage inside sensors. Run a full check before using
in such environments.
• Ensure that the tube is not deformed when using a band to
• Drops of water, bubbles, or haze inside the tube may cause
• Operation may become unstable in the following cases:
• There are some liquids, such as milky white liquids, for
• Do not let the end of the fluororesin section bump into an-
secure the Fiber Unit.
malfunctions.
A Bubbles stick to the cone of the sensing head.
B Solute is deposited on the cone of the sensing head.
C The liquid has a high viscosity.
which detection is not possible.
other object. Damage to, or deformation of, the sensing
head may result in unstable operation.
Amplifier Unit
E3X-DA@-N
E3X-DA@-S
E3X-MDA@
E3X-NA@
E32-D@-S
Fiber Unit
E32-D@
Emission
E32-A07E2
View from the cable drawing side
Reception
Sensing object
5.2±
2
mm (from the end of the
Liquid-level detection
position
fluororesin section)
Reception
E32-A07E1
Emission