ATAM862P-TNSY4D Atmel, ATAM862P-TNSY4D Datasheet - Page 6
![IC MCU FLASH 4K TX 433MHZ 24SSOP](/photos/6/76/67636/453-24-ssop_sml.jpg)
ATAM862P-TNSY4D
Manufacturer Part Number
ATAM862P-TNSY4D
Description
IC MCU FLASH 4K TX 433MHZ 24SSOP
Manufacturer
Atmel
Datasheet
1.ATAM862P-TNQY4D.pdf
(110 pages)
Specifications of ATAM862P-TNSY4D
Applications
UHF ASK/FSK
Core Processor
MARC4
Program Memory Type
FLASH (4 kB)
Controller Series
MARC4 4-Bit
Ram Size
256 x 4
Interface
SSI
Number Of I /o
11
Voltage - Supply
1.8 V ~ 4 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
24-SSOP
Processor Series
ATAM862x
Core
MARC4
Data Bus Width
4 bit
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
6. General Description
7. Functional Description
7.1
7.2
6
ASK Transmission
FSK Transmission
ATAM862-4
The fully-integrated PLL transmitter that allows particularly simple, low-cost RF miniature trans-
mitters to be assembled. The VCO is locked to 32 × f
for a 433.92 MHz transmitter. All other PLL and VCO peripheral elements are integrated.
The XTO is a series resonance oscillator so that only one capacitor together with a crystal con-
nected in series to GND are needed as external elements.
The crystal oscillator together with the PLL needs maximum < 1 ms until the PLL is locked and
the CLK output is stable. A wait time of ≥ 1 ms until the CLK is used for the microcontroller and
the PA is switched on.
The power amplifier is an open-collector output delivering a current pulse which is nearly inde-
pendent from the load impedance. The delivered output power is controllaed via the connected
load impedance.
This output configuration enables a simple matching to any kind of antenna or to 50Ω. A high
power efficiency of η = P
load impedance of Z
If ENABLE = L and PA_ENABLE = L, the circuit is in standby mode consuming only a very small
amount of current so that a lithium cell used as power supply can work for several years.
With ENABLE = H, the XTO, PLL and the CLK driver are switched on. If PA_ENABLE remains
L, only the PLL and the XTO are running and the CLK signal is delivered to the microcontroller.
The VCO locks to 32 times the XTO frequency.
With ENABLE = H and PA_ENABLE = H, the PLL, XTO, CLK driver and the power amplifier are
on. With PA_ENABLE, the power amplifier can be switched on and off, which is used to perform
the ASK modulation.
The PLL transmitter block is activated by ENABLE = H. PA_ENABLE must remain L for
t ≥ 1 ms, then the CLK signal can be taken to clock the microcontroller and the output power
can be modulated by means of pin PA_ENABLE. After transmission, PA_ENABLE is switched to
L and the microcontroller switches back to internal clocking. The PLL transmitter block is
switched back to standby mode with ENABLE = L.
The PLL transmitter block is activated by ENABLE = H. PA_ENABLE must remain L for
t ≥ 1 ms, then the CLK signal can be taken to clock the microcontroller and the power amplifier
is switched on with PA_ENABLE = H. The chip is then ready for FSK modulation. The microcon-
troller starts to switch on and off the capacitor between the XTAL load capacitor and GND with
an open-drain output port, thus changing the reference frequency of the PLL. If the switch is
closed, the output frequency is lower than if the switch is open. After transmission PA_ENABLE
is switched to L and the microcontroller switches back to internal clocking. The PLL transmitter
block is switched back to standby mode with ENABLE = L.
The accuracy of the frequency deviation with XTAL pulling method is about ±25% when the fol-
lowing tolerances are considered.
Load
= (166 + j223)Ω is used at 3V supply voltage.
out
/(I
S,PA
× V
S
) of 36% for the power amplifier results when an optimized
XTAL
, thus, a 13.56 MHz crystal is needed
4551G–4BMCU–07/07