20-101-1051 Rabbit Semiconductor, 20-101-1051 Datasheet - Page 16
![MODULE RABBITCORE RCM3365](/photos/6/74/67489/20-101-1051_sml.jpg)
20-101-1051
Manufacturer Part Number
20-101-1051
Description
MODULE RABBITCORE RCM3365
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1051.pdf
(164 pages)
Specifications of 20-101-1051
Module/board Type
MPU Core Module
Product
Microcontroller Modules
Core Processor
Rabbit 3000
Flash
512 KBytes
Operating Supply Voltage
3.15 to 3.45 V
Board Size
69 mm x 47 mm x 22 mm
For Use With/related Products
RCM3365
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1111
- Current page: 16 of 164
- Download datasheet (3Mb)
2.2 Hardware Connections
There are three steps to connecting the Prototyping Board for use with Dynamic C and the
sample programs:
1. Attach the RCM3365/RCM3375 module to the Prototyping Board.
2. Connect the serial programming cable between the RCM3365/RCM3375 and the worksta-
3. Connect the power supply to the Prototyping Board.
2.2.1 Step 1 — Attach Module to Prototyping Board
Turn the RCM3365/RCM3375 module so that the Ethernet jack is facing the direction shown
in Figure 2 below. Align the pins from headers J3 and J4 on the bottom side of the module into
header sockets JA and JB on the Prototyping Board. The picture card (NAND flash) does not
have to be inserted into connector J6 on the RCM3365/RCM3375 at this time.
Press the module’s pins firmly into the Prototyping Board header sockets—press down in the
area above the header pins using your thumbs or fingers over the header pins as shown in
Figure 2. Do not press down on the picture card connector (J6) unless the picture card is
installed, but rather press down on the circuit board along the edge by the connector. Also, do
not press down on the middle of the module to avoid flexing the module, which could damage
the module or components on the module.
Should you need to remove the module, grasp it with your fingers along the sides by the con-
nectors and gently work the module up to pull the pins away from the sockets where they are
installed. Do not remove the module by grasping it at the top and bottom.
10
tion PC or if you have an RCM3365 with RabbitSys firmware you may connect the
RCM3365 and the PC using Ethernet cables.
NOTE: It is important that you line up the pins on headers J3 and J4 of the RCM3365/
Figure 2. Install the RCM3365/RCM3375 Module on the Prototyping Board
RCM3375 module exactly with the corresponding pins of header sockets JA and JB on
the Prototyping Board. The header pins may become bent or damaged if the pin align-
ment is offset, and the module will not work. Permanent electrical damage to the mod-
ule may also result if a misaligned module is powered up.
RabbitCore RCM3365/RCM3375
Related parts for 20-101-1051
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![20-101-0575](/photos/6/75/67539/20-101-0575_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0576](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0412](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0411](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0457](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
![20-101-0455](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
![20-101-0497](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0456](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
![20-101-0591](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0594](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0602](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0430](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
![20-101-0462](/photos/37/60/376013/bl2100_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
![20-101-0891](/photos/37/60/376014/bl2600_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0654](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: