20-101-1028 Rabbit Semiconductor, 20-101-1028 Datasheet - Page 23
20-101-1028
Manufacturer Part Number
20-101-1028
Description
MODULE RABBITCORE RCM3750
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1028.pdf
(172 pages)
Specifications of 20-101-1028
Module/board Type
MPU Core Module
Product
Microcontroller Modules
Core Processor
Rabbit 3000
Flash
512 KBytes
Operating Supply Voltage
4.75 to 5.25 V
Board Size
75 mm x 30 mm x 23 mm
For Use With/related Products
RCM3750
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1110
- Current page: 23 of 172
- Download datasheet (3Mb)
3.2.1 Use of Serial Flash
The following sample programs can be found in the
and the
•
•
3.2.2 Serial Communication
The following sample programs can be found in the
SAMPLES\RCM3720\SERIAL
•
•
Getting Started
SERIAL_FLASHLOG.C
hits on the home page of the serial flash “server.” This log can be viewed and cleared
from a browser at http://10.10.6.100/. You will likely have to first
work interface card for a “10Base-T Half-Duplex” or an “Auto-Negotiation” connection on the
“Advanced” tab, which is accessed from the control panel (Start > Settings > Control
Panel) by choosing Network Connections.
SFLASH_INSPECT.C
serialflash chip. When the sample program starts running, it attempts to initialize a
serial flash chip on Serial Port B. Once a serial flash chip is found, the user can perform
two different commands to either print out the contents of a specified page or clear (set
to zero) all the bytes in a specified page.
FLOWCONTROL.C
Serial Port C for CTS/RTS with serial data coming from Serial Port D. The serial data
received are displayed in the
To set up the Prototyping Board, you will need to tie TxC and RxC
together on the RS-232 header at J2, and you will also tie TxD and
RxD together using the 0.1" jumpers supplied in the Development Kit
as shown in the diagram.
A repeating triangular pattern should print out in the
The program will periodically switch flow control on or off to demonstrate the effect of
no flow control.
PARITY.C
repeatedly sending byte values 0–127 from Serial Port D to Serial Port
C. The program will switch between generating parity or not on Serial
Port D. Serial Port C will always be checking parity, so parity errors
should occur during every other sequence.
To set up the Prototyping Board, you will need to tie TxD and RxC together on the
RS-232 header at J2 using the 0.1" jumpers supplied in the Development Kit as shown
in the diagram.
The Dynamic C
NOTE: Pin PE5 is set up to enable/disable the RS-232 chip on the RCM3700 Prototyping
SAMPLES\RCM3720\SerialFlash
BitWrPortI(PEDR, &PEDRShadow, 0, 5);//set low to enable rs232 device
Board. This pin will also be toggled when you run RS-232 sample programs on an
RCM3700 Prototyping Board. If you plan to use this pin for something else while you
are running any of the RS-232 sample programs, comment out the following line.
—This program demonstrates the use of parity modes by
STDIO
—This program demonstrates hardware flow control by configuring
—This program is a handy utility for inspecting the contents of a
—This program runs a simple Web server and stores a log of
window will display the error sequence.
folders.
STDIO
window.
folders.
SAMPLES\RCM3700\SerialFlash
SAMPLES\RCM3700\SERIAL
STDIO
window.
“configure” your net-
and the
17
Related parts for 20-101-1028
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: