XC3S400AN-4FGG400C Xilinx Inc, XC3S400AN-4FGG400C Datasheet - Page 65

• Manufacturer Part Number: XC3S400AN-4FGG400C
• Description: IC SPARTAN-3AN FPGA 400K 400FBGA
• Manufacturer: Xilinx Inc
• Series: Spartan™-3ANr

Specifications of XC3S400AN-4FGG400C

• Total Ram Bits: 368640
• Number Of Logic Elements/cells: 8064
• Number Of Labs/clbs: 896
• Number Of I /o: 311
• Number Of Gates: 400000
• Voltage - Supply: 1.14 V ~ 1.26 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 400-BGA
• No. Of Logic Blocks: 8064
• No. Of Gates: 400000
• No. Of Macrocells: 8064
• Family Type: Spartan-3AN
• No. Of Speed Grades: 4
• No. Of I/o's: 311
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 122-1554

External Serial Peripheral Interface (SPI) Configuration Timing
X-Ref Target - Figure 16
Table 57: Timing for External Serial Peripheral Interface (SPI) Configuration Mode
DS557 (v4.1) April 1, 2011
Product Specification
(Open-Drain)
T
T
T
T
T
T
T
PROG_B
CCLK1
CCLKn
MINIT
INITM
CCO
DCC
CCD
PUDC_B
Symbol
VS[2:0]
CSO_B
INIT_B
M[2:0]
CCLK
(Input)
(Input)
(Input)
(Input)
(Input)
MOSI
DIN
Shaded values indicate specifications on attached SPI Flash PROM.
Initial CCLK clock period
CCLK clock period after FPGA loads ConfigRate bitstream option setting
Setup time on VS[2:0] variant-select pins and M[2:0] mode pins before the
rising edge of INIT_B
Hold time on VS[2:0] variant-select pins and M[2:0] mode pins after the
rising edge of INIT_B
MOSI output valid delay after CCLK falling clock edge
Setup time on the DIN data input before CCLK rising clock edge
Hold time on the DIN data input after CCLK rising clock edge
Figure 16: Waveforms for External Serial Peripheral Interface (SPI) Configuration
T
MINIT
Pin initially pulled High by internal pull-up resistor if PUDC_B input is Low.
Pin initially high-impedance (Hi-Z) if PUDC_B input is High. External pull-up resistor required on CSO_B.
<1:1:1>
<0:0:1>
PUDC_B must be stable before INIT_B goes High and constant throughout the configuration process.
T
INITM
T
CCLK1
Description
T
CSS
Command
Mode input pins M[2:0] and variant select input pins VS[2:0] are sampled when INIT_B
goes High. After this point, input values do not matter until DONE goes High, at which
point these pins become user-I/O pins.
(msb)
T
CCO
www.xilinx.com
Spartan-3AN FPGA Family: DC and Switching Characteristics
T
DSU
T
MCCL1
Command
(msb-1)
T
MCCH1
T
DH
Minimum
Data
50
0
T
T
New ConfigRate active
CCLK1
See
See
See
See
See
MCCL n
Data
T
T
Maximum
V
DCC
Table 51
Table 51
Table 55
Table 55
Table 55
–
–
Data
DS529-3_06_102506
T
T
CCLK n
T
CCD
MCCH n
Units
ns
ns
Data
65