FLTR100V10-62Z Lineage Power, FLTR100V10-62Z Datasheet
FLTR100V10-62Z
Specifications of FLTR100V10-62Z
Related parts for FLTR100V10-62Z
FLTR100V10-62Z Summary of contents
Page 1
... Communications equipment n Description The FLTR100V10 Filter Module is designed to reduce the conducted common-mode and differential-mode noise on input or output lines of high-frequency switching power supplies. The module has a maximum current rating provides high insertion loss throughout the frequency range regulated by the U.S. Federal Communications Commission (FCC) and the International Special Committee on Radio Interference (CISPR) for conducted emissions ...
Page 2
... To meet these requirements, external filtering of the power module is often required. When used in conjunction with the recommended external components and layout, the Lineage Power filter module will significantly reduce the conducted differential and common-mode noise returned to the power source. CISPR and FCC class B require- ments can be met by using the filter as described in the following sections ...
Page 3
... Differential-mode Insertion Loss (50 Ω circuit, 500 kHz) Characteristics 200 LFM 2 400 LFM Figure 1. Derating output current vs. Local ambient temperature and Airflow (Vin = 48Vdc) Lineage Power 75 Vdc Input Maximum Maximum Symbol Min R I max I max — — 0 -20 -40 -60 -80 -100 0.1 Figure 2. Typical Common-Mode Insertion Loss Ω ...
Page 4
... Failure Rate in FITs: 10A 8 6A 24.248 11.679 6.89 38.244 18.925 11.388 58.588 29.736 18.227 87.415 45.433 28.336 127.327 67.671 42.899 181.441 98.481 63.394 253.416 140.302 91.632 GND Figure 5. Internal Schematic Lineage Power OUT 8-1324b ...
Page 5
... CASE pin to the V plane. In +48 V applications where the shield plane and the power module case must be tied to a signal, remove C2 in Figures 6 and 7, remove C2 and C7 in Figure 8, and connect the shield plane and CASE pin to the V plane. March 2008 (+) I (–) I Lineage Power ...
Page 6
... Figure 7. Recommended Layout When Used as the Input Filter to a High-Frequency dc-to-dc Converter 6 V (+) I C5 POWER MODULE V (-) SHIELD PLANE FILTER MODULE V (+) (-) I (+) and V I March 2008 V (+) O V (-) O CASE C3 POWER MODULE C1 C4 SHIELD PLANE CASE C2 C3 (–) planes, as should the V (+) and Lineage Power C4 8-1325b V (+) O V (-) O 8-1328d (–) O ...
Page 7
... Note: C1 through C4 and C6 through C9 can be 0.01 µF to 0.1 µF. Select the voltage rating to meet input-to-output isolation requirements. C5 should be the recommended value indicated in the power module data sheet. Figure 8. Recommended Schematic of Filter Module with Two Power Modules Lineage Power 75 Vdc Input Maximum Maximum V ...
Page 8
... It is often useful to make a model of the power card, using copper tape and a vector card, to experiment with various layout and grounding approaches prior to committing to a printed-wiring board. Lineage Power ...
Page 9
... Vdc Input Maximum Maximum Other Considerations (continued) Figure 9. JW075A1 Conducted Noise with Filter 9 9 8-1387(F) Figure 10. JW075A5 Conducted Noise with Filter March 2008 8-1388(F) Lineage Power ...
Page 10
... Dimensions are in millimeters and (inches). Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Top View Side View 0.51 (0.020) Bottom View 3.8 (0.15) 19.05 (0.750) 4.6 (0.18) 10 50.8 (2.00) MAX FLTR100V10 27.9 Filter Module OUT IN (1.10 Vdc Max. IN MAX Adc Max. IN GND ...
Page 11
... March 2008 Recommended Hole Pattern Component-side footprint. Dimensions are in millimeters and (inches). Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Note: Do not route copper paths beneath power module standoffs. Lineage Power 75 Vdc Input Maximum Maximum 4.6 MODULE OUTLINE (0.18 19.05 (0 ...
Page 12
... C,while the Pb-free solder pot is 270 all RoHS-compliant through-hole products can be pro- cessed with paste-through-hole Pb or Pb-free reflow process.If additional information is needed,please con- sult with your Lineage Power representative for more details C.For max.Not March 2008 ...
Page 13
... March 2008 Ordering Information Device Code FLTR100V10 FLTR100V610 FLTR100V810 FLTR100V10-62 FLTR100V10-62Z FLTR100V10Z FLTR100V610Z FLTR100V810Z Option Codes Option Short pin: 2.8 mm ± 0.25 mm (0.110 in. ± 0.010 in.) Short pin: 3.7 mm ± 0.25 mm (0.145 in. ± 0.010 in.) Short pin: 4.6 mm ± 0.25 mm (0.180 in. ± 0.010 in.) ...