ADSP-2184BST-160 Analog Devices Inc, ADSP-2184BST-160 Datasheet - Page 12

• Manufacturer Part Number: ADSP-2184BST-160
• Description: IC DSP CONTROLLER 16BIT 100LQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2184BST-160

• Rohs Status: RoHS non-compliant
• Interface: Host Interface, Serial Port
• Clock Rate: 40MHz
• Non-volatile Memory: External
• On-chip Ram: 20kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP

ADSP-2184
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1 0.1 inches. The pin strip header must have
at least 0.15-inch clearance on all sides to accept the EZ-ICE
probe plug. Pin strip headers are available from vendors such as
3M, McKenzie and Samtec.
Target Memory Interface
For your target system to be compatible with the EZ-ICE emu-
lator, it must comply with the memory interface guidelines listed
below.
PM, DM, BM, IOM, and CM
Design a Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM) and Composite Memory
(CM) external interfaces to comply with worst case device tim-
ing requirements and switching characteristics as specified in
this DSP’s data sheet. The performance of the EZ-ICE may ap-
proach published worst case specifications for some memory
access timing requirements and switching characteristics.
Figure 8. Target Board Connector for EZ-ICE
KEY (NO PIN)
ELOUT
RESET
GND
EBG
EBR
EE
13
11
1
9
3
5
7
TOP VIEW
12
14
10
2
4
6
8
BG
EINT
BR
ELIN
ECLK
EMS
ERESET
–12–
Note: If your target does not meet the worst case chip specifica-
tions for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depend-
ing on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statisti-
cally vary in switching characteristics and timing requirements
within published limits.
Restriction: All memory strobe signals on the ADSP-2184 (RD,
WR, PMS, DMS, BMS, CMS and IOMS) used in your target
system must have 10 k pull-up resistors connected when the
EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
• EZ-ICE emulation introduces an 8 ns propagation delay
• EZ-ICE emulation introduces an 8 ns propagation delay
• EZ-ICE emulation ignores RESET and BR when single-
• EZ-ICE emulation ignores RESET and BR when in Emulator
• EZ-ICE emulation ignores the state of target BR in certain
between your target circuitry and the DSP on the RESET
signal.
between your target circuitry and the DSP on the BR signal.
stepping.
Space (DSP halted).
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (BG) is asserted
by the EZ-ICE board’s DSP.
REV. 0