ADSP-2183KST-210 Analog Devices Inc, ADSP-2183KST-210 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADSP-2183KST-210
Manufacturer Part Number
ADSP-2183KST-210
Description
IC DSP CONTROLLER 16BIT 128-LQFP
Manufacturer
Analog Devices Inc
Series
ADSP-21xxr
Type
Fixed Pointr
Datasheet
1.ADSP-2183BSTZ-160.pdf
(31 pages)
Specifications of ADSP-2183KST-210
Rohs Status
RoHS non-compliant
Interface
Synchronous Serial Port (SSP)
Clock Rate
52MHz
Non-volatile Memory
External
On-chip Ram
80kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
128-LQFP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADSP-2183KST-210
Manufacturer:
AD
Quantity:
16
Company:
Part Number:
ADSP-2183KST-210
Manufacturer:
AD
Quantity:
1 831
Part Number:
ADSP-2183KST-210
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADSP-2183
When the IDLE (n) instruction is used, it effectively slows down
the processor’s internal clock, and thus its response time, to
incoming interrupts. The one-cycle response time of the stan-
dard idle state is increased by n, the clock divisor. When an
enabled interrupt is received, the ADSP-2183 will remain in the
idle state for up to a maximum of n processor cycles (n = 16, 32,
64 or 128) before resuming normal operation.
When the IDLE (n) instruction is used in systems with an exter-
nally generated serial clock (SCLK), the serial clock rate may be
faster than the processor’s reduced internal clock rate. Under
these conditions, interrupts must not be generated at a faster
rate than can be serviced, due to the additional time the processor
takes to come out of the idle state (a maximum of n processor
cycles).
SYSTEM INTERFACE
Figure 2 shows a typical basic system configuration with the
ADSP-2183, two serial devices, a byte-wide EPROM and
optional external program and data overlay memories. Program-
mable wait state generation allows the processor to connect
easily to slow peripheral devices. The ADSP-2183 also provides
four external interrupts and two serial ports or six external inter-
rupts and one serial port.
Clock Signals
The ADSP-2183 can be clocked by either a crystal or a TTL-
compatible clock signal.
The CLKIN input cannot be halted, changed during operation
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual, Third Edition, for detailed
information on this power-down feature.
CONTROLLER
INTERFACE
1/2x CLOCK
SYSTEM
CRYSTAL
OR
DEVICE
DEVICE
SERIAL
SERIAL
OR
16
XTAL
SCLK0
RFS0
TFS0
DT0
DR0
CLKIN
IRD
IWR
IS
IAL
IACK
IAD15-0
FL0-2
PF0-7
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
IDMA PORT
IRQ2
IRQE
IRQL0
IRQL1
SPORT1
SPORT0
ADSP-2183
ADDR13-0
DATA23-0
PWDACK
IOMS
BMS
DMS
CMS
PMS
BGH
PWD
WR
RD
BR
BG
14
24
D
A
23-16
13-0
A
D
A
D
D
10-0
23-8
13-0
23-0
15-8
DATA
CS
DATA
DATA
A0-A21
ADDR
CS
ADDR
(PERIPHERALS)
2048 LOCATIONS
PM SEGMENTS
DM SEGMENTS
SPACE
MEMORY
OVERLAY
MEMORY
I/O
TWO 8K
TWO 8K
BYTE
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-2183 uses an input clock with a frequency equal to
half the instruction rate; a 16.67 MHz input clock yields a 30 ns
processor cycle (which is equivalent to 33 MHz). Normally,
instructions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.
Because the ADSP-2183 includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be connected
across the CLKIN and XTAL pins, with two capacitors connected
as shown in Figure 3. Capacitor values are dependent on crystal
type and should be specified by the crystal manufacturer. A
parallel-resonant, fundamental frequency, microprocessor-grade
crystal should be used.
A clock output (CLKOUT) signal is generated by the processor
at the processor’s cycle rate. This can be enabled and disabled
by the CLKODIS bit in the SPORT0 Autobuffer Control
Register.
Reset
The RESET signal initiates a master reset of the ADSP-2183.
The RESET signal must be asserted during the power-up se-
quence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid V
plied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked, but does
not include the crystal oscillator start-up time. During this
power-up sequence the RESET signal should be held low. On
any subsequent resets, the RESET signal must meet the mini-
mum pulsewidth specification, t
The RESET input contains some hysteresis; however, if you use
an RC circuit to generate your RESET signal, the use of an
external Schmidt trigger is recommended.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When RESET is released, if there is no pending bus
request and the chip is configured for booting (MMAP = 0), the
boot-loading sequence is performed. The first instruction is
fetched from on-chip program memory location 0x0000 once
boot loading completes.
CLKIN
DSP
XTAL
RSP
.
CLKOUT
DD
is ap-