PVZ3A501A01R00 Murata, PVZ3A501A01R00 Datasheet - Page 53

• Manufacturer Part Number: PVZ3A501A01R00
• Description: Trimmer Resistors - SMD 500 OHM SMD 3MM
• Manufacturer: Murata
• Series: PVZ3Ar

Specifications of PVZ3A501A01R00

• Resistance: 500 Ohms
• Tolerance: 30 %
• Power Rating: 0.1 Watt (1/10 Watt)
• Operating Temperature Range: - 25 C to + 85 C
• Element Type: Carbon
• Number Of Turns: 1
• Product: Single-Turn Trimmer Potentiometers
• Taper: Linear
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
2. Mounting
52
PVC6/PV32/PV34 Series Notice
(1) Soldering condition
(2) To minimize mechanical stress when adjusting,
(3) The soldering iron should not come in contact
(1) Use PCB hole to meet the pin of the trimmer
(2) Do not apply excessive force (preferably 9.8N
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
the trimmer potentiometer should be mounted onto
PCB without gap.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
potentiometer. If the trimmer potentiometer
installs into insufficient PCB hole, the
trimmer potentimeter may be damaged by
mechanical stress.
(Ref.; 1kgf) max.), when the trimmer
potentiometer is mounted to the PCB.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
•
R)^1/2 or the
3. Cleaning
If the trimmer potentiometer is cleaned by other
conditions, the trimmer potentiometer may be damaged.
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) The total cleaning time by cold dipping, vapor
(3) For ultra-sonic cleaning, the available
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
applicable solvents for cleaning. If you use
any other types of solvents, please consult with
a Murata factory representative prior to using.
and ultrasonic washing (conditions as below)
method should be less than 3 minutes.
condition is as follows.
Due to the ultra-sonic cleaning equipment's
peculiar self-resonance point and that the
cleaning compatibility usually depends on the
jig construction and/or the cleaning condition
such as the depth of immersion, please check the
cleaning equipment to determine the suitable
conditions.
>Power: 600W (67 liter) max.
>Frequency: 28kHz
>Temperature: Ambient temperature
R50E.pdf
05.9.9