EPM7032SLC44-10N Altera, EPM7032SLC44-10N Datasheet - Page 20
![IC MAX 7000 CPLD 32 44-PLCC](/photos/6/70/67054/544-44-plcc_sml.jpg)
EPM7032SLC44-10N
Manufacturer Part Number
EPM7032SLC44-10N
Description
IC MAX 7000 CPLD 32 44-PLCC
Manufacturer
Altera
Series
MAX® 7000r
Datasheet
1.EPM7064STC44-10.pdf
(66 pages)
Specifications of EPM7032SLC44-10N
Programmable Type
In System Programmable
Delay Time Tpd(1) Max
10.0ns
Voltage Supply - Internal
4.75 V ~ 5.25 V
Number Of Logic Elements/blocks
2
Number Of Macrocells
32
Number Of Gates
600
Number Of I /o
36
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
44-PLCC
Voltage
5V
Memory Type
EEPROM
Number Of Logic Elements/cells
2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Other names
544-2001
EPM7032SLC44-10N
EPM7032SLC44-10N
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EPM7032SLC44-10N
Manufacturer:
ALTERA
Quantity:
4
Company:
Part Number:
EPM7032SLC44-10N
Manufacturer:
ALTERA
Quantity:
8
Company:
Part Number:
EPM7032SLC44-10N
Manufacturer:
ALTERA41
Quantity:
348
Part Number:
EPM7032SLC44-10N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
MAX 7000 Programmable Logic Device Family Data Sheet
Programmable
Speed/Power
Control
Output
Configuration
20
MAX 7000 devices offer a power-saving mode that supports low-power
operation across user-defined signal paths or the entire device. This
feature allows total power dissipation to be reduced by 50% or more,
because most logic applications require only a small fraction of all gates to
operate at maximum frequency.
The designer can program each individual macrocell in a MAX 7000
device for either high-speed (i.e., with the Turbo Bit
or low-power (i.e., with the Turbo Bit option turned off) operation. As a
result, speed-critical paths in the design can run at high speed, while the
remaining paths can operate at reduced power. Macrocells that run at low
power incur a nominal timing delay adder (t
t
MAX 7000 device outputs can be programmed to meet a variety of
system-level requirements.
MultiVolt I/O Interface
MAX 7000 devices—except 44-pin devices—support the MultiVolt I/O
interface feature, which allows MAX 7000 devices to interface with
systems that have differing supply voltages. The 5.0-V devices in all
packages can be set for 3.3-V or 5.0-V I/O pin operation. These devices
have one set of VCC pins for internal operation and input buffers
(VCCINT), and another set for I/O output drivers (VCCIO).
The VCCINT pins must always be connected to a 5.0-V power supply.
With a 5.0-V V
are therefore compatible with both 3.3-V and 5.0-V inputs.
The VCCIO pins can be connected to either a 3.3-V or a 5.0-V power
supply, depending on the output requirements. When the VCCIO pins are
connected to a 5.0-V supply, the output levels are compatible with 5.0-V
systems. When V
3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices
operating with V
timing delay of t
Open-Drain Output Option (MAX 7000S Devices Only)
MAX 7000S devices provide an optional open-drain (functionally
equivalent to open-collector) output for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
EN
, and t
SEXP
, t
CCINT
ACL
OD2
CCIO
CCIO
, and t
level, input voltage thresholds are at TTL levels, and
instead of t
levels lower than 4.75 V incur a nominally greater
is connected to a 3.3-V supply, the output high is
CPPW
parameters.
OD1
.
LPA
) for the t
TM
option turned on)
Altera Corporation
LAD
, t
LAC
, t
IC
,