EPM570GT144C5 Altera, EPM570GT144C5 Datasheet - Page 52
![IC MAX II CPLD 570 LE 144-TQFP](/photos/6/70/67061/544-144-tqfp_sml.jpg)
EPM570GT144C5
Manufacturer Part Number
EPM570GT144C5
Description
IC MAX II CPLD 570 LE 144-TQFP
Manufacturer
Altera
Series
MAX® IIr
Specifications of EPM570GT144C5
Programmable Type
In System Programmable
Delay Time Tpd(1) Max
5.4ns
Voltage Supply - Internal
1.71 V ~ 1.89 V
Number Of Logic Elements/blocks
570
Number Of Macrocells
440
Number Of I /o
116
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
144-TQFP, 144-VQFP
Voltage
1.8V
Memory Type
FLASH
Number Of Logic Elements/cells
570
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Other names
544-1311
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EPM570GT144C5N
Manufacturer:
ALLIANCE
Quantity:
1 000
Part Number:
EPM570GT144C5N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
4–2
I/O Pins Remain Tri-Stated during Power-Up
Signal Pins Do Not Drive the V
AC and DC Specifications
Hot Socketing Feature Implementation in MAX II Devices
MAX II Device Handbook
1
A device that does not support hot-socketing may interrupt system operation or cause
contention by driving out before or during power-up. In a hot socketing situation, the
MAX II device’s output buffers are turned off during system power-up. MAX II
devices do not drive out until the device attains proper operating conditions and is
fully configured. Refer to
about turn-on voltages.
MAX II devices do not have a current path from I/O pins or GCLK[3..0] pins to the
V
(or removed from) a system board that was powered up without damaging or
interfering with system-board operation. When hot socketing, MAX II devices may
have a minimal effect on the signal integrity of the backplane.
You can power up or power down the V
hot socketing, the I/O pin capacitance is less than 8 pF. MAX II devices meet the
following hot socketing specifications:
■
■
MAX II devices are immune to latch-up when hot socketing. If the TCK JTAG input
pin is driven high during hot socketing, the current on that pin might exceed the
specifications above.
I
when the device is being powered up or powered down. This specification takes into
account the pin capacitance but not board trace and external loading capacitance.
Additional capacitance for trace, connector, and loading must be taken into
consideration separately. The peak current duration due to power-up transients is
10 ns or less.
The DC specification applies when all V
powered-up or powered-down conditions.
The hot socketing feature turns off (tri-states) the output buffer during the power-up
event (either V
generates an internal HOTSCKT signal when either V
threshold voltage during power-up or power-down. The HOTSCKT signal cuts off the
output buffer to make sure that no DC current (except for weak pull-up leaking) leaks
through the pin. When V
relatively low even after the power-on reset (POR) signal is released and device
configuration is complete.
IOPIN
CCIO
The hot socketing DC specification is: | I
The hot socketing AC specification is: | I
is the current at any user I/O pin on the device. The AC specification applies
or V
CCINT
pins before or during power-up. A MAX II device may be inserted into
CCINT
CCIO
or V
or V
CCINT
CCIO
CC
“Power-On Reset Circuitry” on page 4–5
ramps up very slowly during power-up, V
Power Supplies
supplies) or power-down event. The hot-socket circuit
Chapter 4: Hot Socketing and Power-On Reset in MAX II Devices
CC
CCIO
supplies to the device are stable in the
and V
IOPIN
IOPIN
Hot Socketing Feature Implementation in MAX II Devices
| < 300 A.
| < 8 mA for 10 ns or less.
CCINT
CCINT
pins in any sequence. During
or V
© October 2008 Altera Corporation
CCIO
is below the
for information
CC
may still be