SMM0204AC1000FB300 Vishay, SMM0204AC1000FB300 Datasheet
SMM0204AC1000FB300
Manufacturer Part Number
SMM0204AC1000FB300
Description
Manufacturer
Vishay
Datasheet
1.SMM0204AC1000FB300.pdf
(7 pages)
www.vishay.com
30
SMM0204
Vishay Draloric
Notes
• SMM0204 EN803 E0 and OMM0204 EN803 E0 respectively are available versions with IECQ-CECC approval to EN 140401-803, version A,
• The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
Notes
• The upper temperature limit of 125 °C reflects the prescriptions of the detail specification EN 140401-803. However, the products may be
• The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
• The specification of this product is based on a test board according to EN 140400, providing a thermal resistance of approximately 220 K/W.
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
• The IECQ-CECC approved product versions SMM0204 EN803 E0 and OMM0204 EN803 E0 respectively feature a quality factor
** Please see document “Vishay Material Category Policy”:
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
SMM0204
SMM0204
SMM0204
SMM0204
Zero-Ohm-Resistor: OMM0204
TECHNICAL SPECIFICATIONS
PARAMETER
Power rating P
Limiting element voltage, DC or AC
Insulation voltage (1 min), DC or AC
Insulation resistance
Category temperature range
Failure rate: FIT
with nominal failure rate level E0.
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
operated up 155 °C, if the tradeoff through decreased drift stability is acceptable to the specific application.
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 125 °C or 155 °C respectively
is not exceeded.
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
the purpose of system MTBF calculations, compared with
70
observed
POWER RATING
0.25
0.25
0.25
0.25
P
W
70
RMS
PEAK
Thin Film Mini-MELF Resistors
R
max.
LIMITING ELEMENT
For technical questions, contact:
DC or AC
= 10 m
VOLTAGE
This document is subject to change without notice.
200
200
200
200
V
RMS
www.vishay.com/doc?99902
Q
= 10 for the standard versions.
I
UNIT
max.
°C
W
V
V
TEMPERATURE
COEFFICIENT
= 3 A
ppm/K
± 100
FEATURES
Advanced thin film technology
AEC-Q200 qualified
Low TCR and tight tolerances
Excellent stability in different environmental
Pure tin termination on nickel barrier, plated on
Compliant to RoHS Directive 2002/95/EC
± 15
± 25
± 50
conditions
press fit steel caps
melf@vishay.com
0.1 x 10
TOLERANCE
± 0.25
± 0.25
± 0.1
± 0.5
± 0.1
± 0.5
±0.5
± 1
± 5
%
-9
/h
RESISTANCE
- 55 to + 125 (+ 155)
43R to 221K
22R to 221K
10R to 221K
43R to 511K
22R to 511K
10R to 1M0
10R to 1M0
R82 to 10M
R22 to 10M
RANGE
SMM0204
10
0.25
200
300
Document Number: 20004
www.vishay.com/doc?91000
10
Revision: 16-Sep-11
24; 96; 192
24; 96; 192
24; 96; 192
E-SERIES
24; 96
24
Q
= 3 for