MAL212835109E3 Vishay, MAL212835109E3 Datasheet - Page 9

• Manufacturer Part Number: MAL212835109E3
• Manufacturer: Vishay

Table 3
Revision: 23-Aug-11
TEST PROCEDURES AND REQUIREMENTS
Endurance
Useful life
Shelf life (storage at
high temperature)
Charge and discharge
Solvent resistance
Extended vibration
Shock
Passive flammability
NAME OF TEST
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
www.vishay.com
TEST
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
IEC 60695-2-2
IEC 60384-4/
EN130300
subclause 4.13
CECC 30302
subclause 1.8.1
IEC 60384-4/
EN130300
subclause 4.17
IEC 60384-4-2
subclause 9.21
IEC 60068-2-45,
test XA
IEC 60653
IEC 60068-2-6
test Fc
IEC 60068-2-27
test Ea
REFERENCE
For technical questions, contact:
T
U
U
10 000 h
T
I
U
U
20 000 h
T
500 h
10
0.5 s to U
0.5 s to ground
Immersion: 5 min ± 0.5 min with or without
ultrasonic at 55 °C ± 5 °C
Solvents: demineralized water and/or calgonite
solution (20 g/l)
10 Hz to 2000 Hz; 1.5 mm or 20 g;
1 octave/min; 3 directions;
1 sweep per direction; no voltage applied
Half-sine or sawtooth pulse shape; 50 g; 11 ms;
3 successive shocks in each direction of
3 mutually perpendicular axes;
no voltage applied
Capacitor mounted to a vertical printed-circuit
board, one flame on capacitor body;
T
test duration = 20 s
R
amb
amb
amb
amb
R
R
R
R
applied and:
6
= 6.3 V to 25 V with U
= 40 V with U
= 6.3 V to 25 V with U
= 40 V with U
cycles without series resistance:
= 125 °C;
= 125 °C;
= 125 °C; no voltage applied;
= 20 °C to 25 °C;
R
;
(quick reference)
PROCEDURE
9
C
C
applied;
applied;
[e-mail]
R
R
applied;
applied;
www.vishay.com/doc?91000
Vishay BCcomponents
C/C: ± 10 %
tan   1.2 x spec. limit
Z  1.2 x spec. limit
I
C/C: ± 15 %
tan   1.5 x spec. limit
Z  1.5 x spec. limit
I
no short or open circuit,
no visible damage
total failure percentage: < 1 %
C/C: ± 10 %
tan   1.2 x spec. limit
I
C/C: ± 5 %
no short or open circuit,
no visible damage
Visual appearance not affected
no intermittent contacts
no breakdown
no open circuiting
no mechanical damage
C/C: ± 5 %
tan   1.2 x spec. limit
Z  1.2 x spec. limit
I
no intermittent contacts
no breakdown
no open circuiting
no mechanical damage
C/C: ± 5 %
tan   1.2 x spec. limit
Z  1.2 x spec. limit
I
After removing the test flame from
the capacitor, the capacitor must
not continue to burn for more than
15 s; no burning particles must drop
from the sample
L5
L5
L5
L5
L5
 spec. limit
 spec. limit
 spec. limit
 1.5 x spec. limit
 1.5 x spec. limit
128 SAL-RPM
REQUIREMENTS
Document Number: 28354