LQ057Q3DG01 Sharp Electronics, LQ057Q3DG01 Datasheet

Page 1

TECHNICAL TFT - LCD module ＬＱ０５７Ｑ３ＤＧ０１ MODEL No. These parts have corresponded with the RoHS directive. The technical literature is subject to change without notice. So, please contact Sharp or its representative before designing your product based on this literature. ...

Page 2

RECORDS OF REVISION ＭＯＤＥＬ Ｎｏ：ＬＱ０５７Ｑ３ＤＧ０１ ＳＰＥＣ Ｎｏ ：ＬＤ－２０Ｚ５３Ａ NO. PAGE 2008/12/19 A SUMMARY Issued NOTE 1 Issue st ...

Page 3

NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for ...

Page 4

... Application technical literature This applies to color TFT-LCD module, LQ057Q3DG01. 2. Summary and Features This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuit (PWB), FPC, front and back polarizer, sealed case, backlight unit, Touch Panel. Graphics and texts can be displayed on a 320× ...

Page 5

Input terminal 4-1. TFT-LCD panel driving part CN1 Used connector: IMSA-9637S-33Y902 (IRISO ELECTRONICS CO.,LTD.) Table 4-1 Functional table of CN1 terminals Pin No. Symbol １ GND ground ２ CK Clock signal for sampling each data signal ３ Hsync Horizontal ...

Page 6

ENAB signal. Don’t keep ENAB “Low” during operation. 【Note 4-2】 R/L = L，U R/L = L，U 4-2. LED Backlight driving part ...

Page 7

Touch Panel part (FPC2) Table 4-3 Functional table of FPC terminals Pin No. Description １ X+ ２ Y+ ３ X- ４ Y- Suitable connector ： IMSA-9617S-04-AGF Table 4-4 TP basic specification Parameters Input voltage Resistor between terminals (X-,X+) Resistor ...

Page 8

Electrical characteristics 6-1. TFT-LCD panel driving section Table 6-1 Parameter +3.3V Supply voltage power suply Current dissipation Permissive input ripple Input Low voltage Input High voltage Input leak current (Low) Input leak current (High) 【Note 6-1】 Vcc turn-on/off conditions. ...

Page 9

Backlight driving section The backlight system is edge-lighting type with 20 White-LED(White Light Emitting Diode). The characteristics of White-LED are shown in the following table. ( deg.) Table 6-2 Parameter LED voltage LED current range Number of ...

Page 10

Horizontal display position Table 7-2 Parameter Enable signal Setup time Pulse width Hsync-Enable signal phase difference Please do not make ENAB fixation in "L". The Horizontal display start position (The) is fixed 7 clock. 7-3. Vertical display position The ...

Page 11

THp Horizontal sync. 0.9Vcc signal 0.1Vcc 0.1Vcc （Hsync） THc Clock signal 0.1Vcc （CK） C1＊ C5＊ C6＊ C7＊ (Number of clock count) Data（R0～5、 Horizintal invalid data period G0～5、B0～5） The 0.9Vcc Data Enable signal （ENAB） TVp Vertical Sync signal 0.1Vcc （Vsync） TVh ...

Page 12

Input Signals, Basic Display Color and Gray Scale of Each Color Colors & Gray scale Gray Scale － Black 0 0 － Blue 0 0 － Green 0 0 － Cyan 0 0 － Red 1 ...

Page 13

Optical characteristics Table 9-1 Parameter Symbol θ 21, θ 22 θ11 Viewing angle range θ12 Contrast ratio CRmax τr Response Rise τd time Fall White chromaticity x y Luminance Y LED life time - TouchPanel transmittance Remarks:The o ptical ...

Page 14

Viewing angle range is defined as follows. θ12 6 o’clock direction The best viewing angle of this module is slightly leaned to 12 o’clock from normal line. Where θ ＞θ , gray scale is reversed partially. 11 max ...

Page 15

Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b)Our TFT-LCD module is designed to be fixed to the hardware with mounting holes on 4-corners on the backside. Be sure to ...

Page 16

Reliability Test Items No. Test items １ High temperature storage test ２ Low temperature storage test ３ High temperature and high humidity operating test ４ High temperature operating test ５ Low temperature operating test ６ Strength against ESD ７ ...

Page 17

...