DS90LV032AWGQML/NOPB National Semiconductor, DS90LV032AWGQML/NOPB Datasheet - Page 3
![](/photos/31/41/314102/16pin_cpak_sml.jpg)
DS90LV032AWGQML/NOPB
Manufacturer Part Number
DS90LV032AWGQML/NOPB
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90LV032AWGQMLNOPB.pdf
(12 pages)
Specifications of DS90LV032AWGQML/NOPB
Number Of Elements
4
Number Of Receivers
4
Number Of Drivers
4
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
100mV
Diff. Input Low Threshold Volt
-100mV
Transmission Data Rate
400Mbps
Propagation Delay Time
3.3ns
Power Dissipation
1.025W
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
16
Lead Free Status / Rohs Status
Compliant
t
t
t
t
t
t
t
t
t
t
t
t
f
Symbol
PHLD
PLHD
SKD1
SKD2
SKD3
SKD4
TLH
THL
PHZ
PLZ
PZH
PZL
MAX
Switching Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified.
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise
specified.
Note 3: All typicals are given for: V
Note 4: Generator waveform for all tests unless otherwise specified: f = 1 MHz, Z
Note 5: The VCMR range is reduced for larger VID. Example: if VID = 400mV, the VCMR is 0.2V to 2.2V. The fail-safe condition with inputs shorted is valid over
a common-mode range of 0V to 2.3V. A VID up to V
delay and Differential Pulse skew decrease when VID is increased from 200mV to 400mV. Skew specifications apply for 200mV
mode range .
Note 6: t
Note 7: t
any event on the inputs.
Note 8: t
V
Note 9: t
operating temperature and voltage ranges, and across process distribution. t
Note 10: ESD Rating:
Note 11: Output short circuit current (I
exceed maximum junction temperature specification.
Note 12: C
Note 13: V
with AC specifications, the common voltage range is 0.1V to 2.3V
Note 14: f
cycle, V
CC
, and within 5°C of each other within the operating temperature range.
HBM (1.5 kΩ, 100 pF)
EIAJ (0Ω, 200 pF)
OL
SKD1
SKD4
SKD2
SKD3
Differential Propagation Delay High to Low
Differential Propagation Delay Low to High
Differential Pulse Skew |t
Differential Channel-to-Channel Skew-same device
Differential Part to Part Skew
Differential Part to Part Skew
Rise Time
Fall Time
Disable Time High to Z
Disable Time Low to Z
Enable Time Z to High
Enable Time Z to Low
Maximum Operating Frequency
MAX
(max 0.4V), V
L
CC
includes probe and jig capacitance.
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over recommended
, Channel-to-Channel Skew, is defined as the difference between the propagation delay of one channel and that of the others on the same chip with
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices at the same
is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel
generator input conditions: t
is always higher than R
≥
OH
250V
≥
(min 2.7V), Load = 10 pF (stray plus probes)
4.5kV
CC
OS
IN+
= +3.3V, T
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not
PHLD
Parameter
and R
r
= t
f
(Note
(Note
− t
< 1ns (0% to 100%), 50% duty cycle, differential (1.05V to 1.35V peak to peak). Output Criteria: 60%/40% duty
IN−
A
(Note
PLHD
voltage. R
= +25°C.
CC
8)
9)
− 0V may be applied to the R
|
(Note
14)
IN−
and R
6)
IN+
are allowed to have a voltage range −0.2V to V
(Note
SKD4
3
is defined as |Max − Min| differential propagation delay.
7)
O
= 50Ω, t
IN+
/ R
C
V
R
C
(Figure 3
ID
(Figure 1
L
L
L
All Channels Switching
IN−
= 10 pF
= 2 kΩ
= 10 pF
= 200 mV
r
and t
inputs with the Common-Mode voltage set to V
Conditions
f
and
(0% to 100%)
and
Figure
(Note
Figure
4)
≤
3,
2)
3 ns for R
Note
CC
− VID/2. However, to be compliant
Min
200
4,
1.8
1.8
≤
0
0
IN
Note
VID
.
≤
7,
0.35
0.35
800mV over the common-
Typ
250
0.1
0.1
11
11
8
6
Note
CC
/2. Propagation
8)
Max
0.35
www.national.com
3.3
3.3
0.5
1.0
1.5
1.2
1.2
12
12
17
17
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns