LB26SKG01-5C24-JB NKK Switches, LB26SKG01-5C24-JB Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/479/nkk_switches_sml.jpg)
LB26SKG01-5C24-JB
Manufacturer Part Number
LB26SKG01-5C24-JB
Description
Manufacturer
NKK Switches
Type
Alternate Contactr
Datasheet
1.LB26SKG01-5C24-JB.pdf
(12 pages)
Specifications of LB26SKG01-5C24-JB
Pole Throw Configuration
DPDT
Switch Configuration
ON ON
Actuator Style
Square Button
Current Rating (max)
0.1A
Illumination Type
Led
Ac Voltage Rating (max)
28VVAC
Dc Voltage Rating (max)
28VVDC
Contact Material
Copper
Contact Plating
Gold
Mechanical Life
200000
Product Height (mm)
34mm
Product Depth (mm)
17.8mm
Product Length (mm)
17.8mm
Operating Temp Range
-25C to 50C
Mounting Style
Panel
Terminal Type
Quick Connect/Solder
Lead Free Status / Rohs Status
Compliant
NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
Align projections on lamp with
grooves (B) in holder when
inserting lamp. To correctly join
the lamp holder and cap base,
match the cut corners (A).
Incandescent & Neon Lamps
Match projection (C) on cap
assembly with groove (C)
inside switch. Lamp terminals
will then be aligned correctly
with lamp socket.
Snap-in clip holds all switches firmly
in place.
To mount round
switch, match
the antirotation
projection on
switch with
guide cut in
panel. Snap
into panel
cutout.
AT607 & AT607N
C
Square
Snap-in Mount
C
Projection
Panel
B
B
A
For panel seal models,
Bright LED must first be
inserted into the lamp
socket which is built into
the switch. The cap can
then be placed on the
switch.
Panel Seal Models
Match clip on cap assembly with receptacle inside
switch. Lamp terminals will then be aligned correctly
with lamp socket.
ASSEMBLY INSTRUCTIONS
Insert switch from the
front of the panel with
the o-ring between the
built-in bezel and the
panel. Install mounting
nut AT075 (supplied with
switch) from the rear of
the panel.
Overtightening mounting
nut may damage the
switch housing.
Lamp Installation & LED Orientation
Installation & Maintenance
Bushing Mount
Bright LED AT627
Switch & Cap Assembly
Panel Seal
Round & Rectangular
Standard Size Pushbuttons
For snap-in models,
Bright LED must be
inserted into the cap
first. Align cut corners
Snap-in Models
C
(C) when
inserting
the LED.
O-ring
Mounting Nut
Bezel
LED
Panel
Cap Extractor
With Lamps AT607, AT607N, and
LEDs AT614, AT625, AT631, AT632:
Match projection on cap assembly with
notch inside switch. Lamp terminals
will then be aligned correctly with lamp
socket.
Align D-flat on LED with flat (B) in
holder when inserting the LED.
To correctly join the lamp holder and
cap base, match the cut corners (A).
AT109
Projection
Actuator must be in UP position.
Pull off cap with cap extractor
AT109.
Replace lamp and reassemble as
shown above.
Notch
Bright & Super Bright LEDs
AT625, AT631, AT632,
Cut Corner
Panel Seal
Lamp Replacement
Series LB
AT635
LED
Sensitive Devices
Socket Wrench
D Flat
Attention
Rubber Seal
Electrostatic
A
AT112
Projection
03-07
B