MT47H64M16HW-3EL IT:E Micron Technology Inc, MT47H64M16HW-3EL IT:E Datasheet - Page 17
MT47H64M16HW-3EL IT:E
Manufacturer Part Number
MT47H64M16HW-3EL IT:E
Description
Manufacturer
Micron Technology Inc
Type
DDR2 SDRAMr
Datasheet
1.MT47H64M16HW-3EL_ITE.pdf
(135 pages)
Specifications of MT47H64M16HW-3EL IT:E
Organization
64Mx16
Density
1Gb
Address Bus
16b
Access Time (max)
450ps
Maximum Clock Rate
667MHz
Operating Supply Voltage (typ)
1.8V
Package Type
FBGA
Operating Temp Range
-40C to 85C
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Supply Current
220mA
Pin Count
84
Mounting
Surface Mount
Operating Temperature Classification
Industrial
Lead Free Status / Rohs Status
Not Compliant
Table 3: FBGA 84-Ball – x16 and 60-Ball – x4, x8 Descriptions
PDF: 09005aef821ae8bf
Rev. O 9/08 EN
M8, M3, M7,
N2, N8, N3,
N7, P2, P8,
L2, L3, L1
Number
x16 Ball
P3, M2,
P7, R2
J8, K8
K2
L8
–
x4, x8 Ball
H8, H3, H7,
G2, G3, G1
J7, K2, K8,
Number
J2, J8, J3,
K3, H2,
K7, L2,
E8, F8
G8
L8
F2
–
A11, A12,
BA0–BA2
A11, A12
Symbol
A9, A10,
A9, A10,
CK, CK#
A0–A2,
A3–A5,
A6–A8,
A0–A2,
A3–A5,
A6–A8,
A13
CKE
CS#
Input
Input
Input
Input
Input
Input
Type
Description
Address inputs: Provide the row address for ACTIVATE com-
mands, and the column address and auto precharge bit (A10) for
READ/WRITE commands, to select one location out of the memory
array in the respective bank. A10 sampled during a PRECHARGE
command determines whether the PRECHARGE applies to one
bank (A10 LOW, bank selected by BA[2:0] or all banks (A10 HIGH).
The address inputs also provide the op-code during a LOAD MODE
command.
Address inputs: Provide the row address for ACTIVATE com-
mands, and the column address and auto precharge bit (A10) for
READ/WRITE commands, to select one location out of the memory
array in the respective bank. A10 sampled during a PRECHARGE
command determines whether the PRECHARGE applies to one
bank (A10 LOW, bank selected by BA[2:0] or all banks (A10 HIGH).
The address inputs also provide the op-code during a LOAD MODE
command.
Bank address inputs: BA[2:0] define to which bank an ACTIVATE,
READ, WRITE, or PRECHARGE command is being applied. BA[2:0]
define which mode register, including MR, EMR, EMR(2), and
EMR(3), is loaded during the LOAD MODE command.
Clock: CK and CK# are differential clock inputs. All address and con-
trol input signals are sampled on the crossing of the positive edge
of CK and negative edge of CK#. Output data (DQ and DQS/DQS#)
is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered
LOW) deactivates clocking circuitry on the DDR2 SDRAM. The specif-
ic circuitry that is enabled/disabled is dependent on the DDR2
SDRAM configuration and operating mode. CKE LOW provides pre-
charge power-down and SELF REFRESH operations (all banks idle),
or ACTIVATE power-down (row active in any bank). CKE is synchro-
nous for power-down entry, power-down exit, output disable, and
for self refresh entry. CKE is asynchronous for self refresh exit. In-
put buffers (excluding CK, CK#, CKE, and ODT) are disabled during
power-down. Input buffers (excluding CKE) are disabled during self
refresh. CKE is an SSTL_18 input but will detect a LVCMOS LOW lev-
el after Vdd is applied during first power-up. After Vref has be-
come stable during the power-on and initialization sequence, it
must be maintained for proper operation of the CKE receiver. For
proper SELF REFRESH operation, Vref must be maintained.
Chip select: CS# enables (registered LOW) and disables (registered
HIGH) the command decoder. All commands are masked when CS#
is registered high. CS# provides for external bank selection on sys-
tems with multiple ranks. CS# is considered part of the command
code.
17
Micron Technology, Inc. reserves the right to change products or specifications without notice.
Ball Assignments and Descriptions
1Gb: x4, x8, x16 DDR2 SDRAM
© 2004 Micron Technology, Inc. All rights reserved.