DS90CR481VJDX/NOPB National Semiconductor, DS90CR481VJDX/NOPB Datasheet - Page 15
![](/photos/31/30/313088/100pin_tqfp_sml.jpg)
DS90CR481VJDX/NOPB
Manufacturer Part Number
DS90CR481VJDX/NOPB
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90CR481VJDXNOPB.pdf
(21 pages)
Specifications of DS90CR481VJDX/NOPB
Number Of Elements
8
Number Of Receivers
48
Number Of Drivers
8
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Output Type
Serializer
Differential Output Voltage
450mV
Transmission Data Rate
5376Mbps
Power Dissipation
2.3W
Operating Temp Range
-10C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Package Type
TQFP
Lead Free Status / Rohs Status
Compliant
Applications Information
current data disparity is zero or negative, the data shall be
sent inverted. If the running word disparity is zero, the data
shall be sent inverted.
DC Balance mode is set when the BAL pin on the transmitter
is tied HIGH - see pin descriptions. DC Balancing is useful
on long cable applications which are typically greater than 5
meters in length.
3. Deskew
Deskew is supported in the DC Balance mode only (BAL =
high on DS90CR481). The “DESKEW” pin on the receiver
when set high will deskew a minimum of
time skew from the ideal strobe location between signals
arriving on independent differential pairs (pair-to-pair skew).
It is required that the “DS_OPT” pin on the Transmitter must
be applied low for a minimum of four clock cycles to com-
plete the deskew operation. It is also required that this must
be performed at least once at any time after the PLLs have
locked to the input clock frequency. If power is lost, or if the
cable has been switched, this procedure must be repeated
or else the receiver may not sample the incoming LVDS data
correctly. When the receiver is in the deskew mode, all
receiver outputs are set to a LOW state, but the receiver
clock output is still active and switching. Setting the
“DESKEW” pin to low will disable the deskew operation and
allow the receiver to operation on a fixed data sampling
strobe. In this case, the ”DS_OPT” pin on the transmitter
must then be set high.
The DS_OPT pin at the input of the transmitter
(DS90CR481) is used to initiate the deskew calibration pat-
tern. It must be applied low for a minimum of four clock
cycles in order for the receiver to complete the deskew
operation. For this reason, the LVDS clock signal with
DS_OPT applied high (active data sampling) shall be
1111000 or 1110000 pattern. During the deskew operation
with DS_OPT applied low, the LVDS clock signal shall be
1111100 or 1100000 pattern. The transmitter will also output
a series of 1111000 or 1110000 onto the LVDS data lines
(TxOUT 0-7) during deskew so that the receiver can auto-
matically calibrated the data sampling strobes at the receiver
inputs. Each data channel is deskewed independently and is
tuned with a step size of 1/3 of a bit time over a range of +/−1
TBIT from the ideal strobe location. The Deskew feature
operates up to clock rates of 80 MHz only. If the Receiver is
enabled in the deskew mode, then it must be trained before
data transfer.
CLOCK JITTER
The transmitter is designed to reject cycle-to-cycle jitter
which may be seen at the transmitter input clock. Very low
cycle-to-cycle jitter is passed on to the transmitter outputs.
Cycle-to-cycle jitter has been measured over frequency to
be less than 100 ps with input step function jitter applied.
This should be subtracted from the RSKM/RSKMD budget
as shown and described in Figure 13 and Figure 14. This
rejection capability significantly reduces the impact of jitter at
the TXinput clock pin, and improves the accuracy of data
sampling in the receiver. Transmitter output jitter is effected
by PLLVCC noise and input clock jitter - minimize supply
noise and use a low jitter clock source to limit output jitter.
The falling edge of the input clock to the transmitter is the
critical edge and is used by the PLL circuit.
±
1 LVDS data bit
(Continued)
15
RSKM - RECEIVER SKEW MARGIN
RSKM is a chipset parameter and is explained in AN-1059 in
detail. It is the difference between the transmitter’s pulse
position and the receiver’s strobe window. RSKM must be
greater than the summation of: Interconnect skew, LVDS
Source Clock Jitter (TJCC), and ISI (if any). See Figure 13.
Interconnect skew includes PCB traces differences, connec-
tor skew and cable skew for a cable application. PCB trace
and connector skew can be compensated for in the design of
the system. Cable skew is media type and length dependant.
RSKMD - RECEIVER SKEW MARGIN WITH DESKEW
RSKMD is a chipset parameter and is applicable when the
DESKEW feature of the DS90CR482 is employed. It is the
difference between the receiver’s strobe window and the
ideal pulse locations. The DESKEW feature adjusts for skew
between each data channel and the clock channel. This
feature is supported up to 80MHz clock rate. RSKMD must
be greater than the summation of: Transmitter’s Pulse Posi-
tion variance, LVDS Source Clock Jitter (TJCC), and ISI (if
any). See Figure 14. With DESKEW, RSKMD will be a
minimum of 25% of TBIT. Deskew compensates for intercon-
nect skew which includes PCB traces differences, connector
skew and cable skew (for a cable application). PCB trace
and connector skew can be compensated for in the design of
the system. Note, cable skew is media type and length
dependant. Cable length may be limited by the RSKMD
parameter prior to the interconnect skew reaching 1 TBIT in
length due to ISI effects.
POWER DOWN
Both transmitter and receiver provide a power down feature.
When asserted current draw through the supply pins is
minimized and the PLLs are shut down. The transmitter
outputs are in TRI-STATE when in power down mode. The
receiver outputs are forced to a active LOW state when in
the power down mode. (See Pin Description Tables). The PD
pin should be driven HIGH to enable the device once V
stable.
CONFIGURATIONS
The transmitter is designed to be connected typically to a
single receiver load. This is known as a point-to-point con-
figuration. It is also possible to drive multiple receiver loads if
certain restrictions are made. Only the final receiver at the
end of the interconnect should provide termination across
the pair. In this case, the driver still sees the intended DC
load of 100 Ohms. Receivers connected to the cable be-
tween the transmitter and the final receiver must not load
down the signal. To meet this system requirement, stub
lengths from the line to the receiver inputs must be kept very
short.
CABLE TERMINATION
A termination resistor is required for proper operation to be
obtained. The termination resistor should be equal to the
differential impedance of the media being driven. This should
be in the range of 90 to 132 Ohms. 100 Ohms is a typical
value common used with standard 100 Ohm twisted pair
cables. This resistor is required for control of reflections and
also to complete the current loop. It should be placed as
close to the receiver inputs to minimize the stub length from
the resistor to the receiver input pins.
www.national.com
CC
is