X1205S8IZ Intersil, X1205S8IZ Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
X1205S8IZ
Manufacturer Part Number
X1205S8IZ
Description
Manufacturer
Intersil
Datasheet
1.X1205S8IZ.pdf
(22 pages)
Specifications of X1205S8IZ
Date Format
DW:DM:M:Y
Time Format
HH:MM:SS
Operating Supply Voltage (typ)
3.3/5V
Package Type
SOIC
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
2.7V
Operating Temperature Classification
Industrial
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Pin Count
8
Mounting
Surface Mount
Lead Free Status / Rohs Status
Compliant
Notes: (1) The device enters the Active state after any start, and remains active: for 9 clock cycles if the Device Select Bits in the Slave Address
Capacitance T
Notes: (1) This parameter is not 100% tested.
AC CHARACTERISTICS
AC Test Conditions
Figure 1. Standard Output Load for testing the device with V
Input Pulse Levels
Input Rise and Fall Times
Input and Output Timing
Levels
Output Load
Symbol
C
Equivalent AC Output Load Circuit for V
C
OUT
IN
(2) The device enters the Program state 200nS after a stop ending a write operation and continues for t
(3) The device goes into the Timekeeping state 200nS after any stop, except those that initiate a nonvolatile write cycle; t
(4) For reference only and not tested.
(5) V
(6) V
(7) V
(8) V
(9) V
(10)V
(11)I
(13)Threshold voltages based on the higher of Vcc or Vback.
(14)Using recommended crystal and oscillator network applied to X1 and X2 (25°C).
(15)Typical values are for T
(2) The input capacitance between x1 and x2 pins can be varied between 5pF and 19.75pF by using analog trimming registers
(1)
(1)
SDA
Byte are incorrect or until 200nS after a stop ending a read or write operation.
that initiates a nonvolatile write cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave
Address Byte.
OL
IL
CC
BACK
SDA
SDA
SDA
= V
= 3.0mA at 5V, 1mA at 2.7V
= 0V
Output Capacitance (SDA, IRQ)
Input Capacitance (SCL)
= V
=V
= GND or V
= 0V
CC
A
SCL
SCL
= 25°C, f = 1.0 MHz, V
x 0.1, V
=V
=V
5.0V
BACK
CC
CC
IH
, Others = GND or V
1533Ω
, Others = GND or V
100pF
, V
= V
4
SCL
A
CC
= 25°C
x 0.9, f
= GND or V
Parameter
V
10ns
V
Standard Output Load
CC
CC
For V
and I
SCL
x 0.1 to V
x 0.5
OL
OL
= 400KHz
CC
CC
CC
= 0.4V
= 3 mA
BACK
CC
= 5V
= 5V
CC
x 0.9
X1205
CC
Max.
IRQ
10
10
= 5.0V
5.0V
Units
pF
pF
1316Ω
806Ω
WC
.
Test Conditions
100pF
V
V
OUT
IN
= 0V
= 0V
WC
after a stop
May 2, 2006
FN8097.3