LQ10D421 Sharp Electronics, LQ10D421 Datasheet
LQ10D421
Specifications of LQ10D421
Available stocks
Related parts for LQ10D421
LQ10D421 Summary of contents
Page 1
... P S roduct pecifications LQ10D421 TFT-LCD Module Spec. Issue Date: June 30, 2000 Liquid Crystal Displays Group No: LD-12610B ...
Page 2
...
Page 3
... Application This specification applies to color TFT-LCD module, LQ10D421 (This specification is only applied for the module which has letter "A" at the end of the lot number of the module.) These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 4
Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1.Note: excluding backlight cables. Outline dimensions is shown in Fig.1 Specifications 26 (10.4") Diagonal 211.2(H)×158.4(V) 640(H)×480(V) (1 ...
Page 5
Input Terminals 4-1. TFT-LCD panel driving 1 2 CN1 pin arrangement from module surface (Transparent view) Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 Hsync Horizontal synchronous signal 4 Vsync Vertical synchronous ...
Page 6
Backlight driving CN2、CN3 Pin no. Symbol Ｖ 1 Power supply for lamp HIGH (High voltage side This is electrically opened. Ｖ 3 Power supply for lamp LOW (Low voltage side) 5. Absolute Maximum Ratings ...
Page 7
Electrical Characteristics 6-1.TFT-LCDpaneldriving Ta＝25℃ Parameter Power Supply voltage Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) 【 NOTE 1】 Vcc-turn-on conditions ０＜Ｔ１≦１５ｍｓ ０＜Ｔ２≦１０ｍｓ ０＜Ｔ３≦１００ｍｓ ０＜Ｔ４≦１ｓ Ｔ５＞２００ｍｓ Vcc-dip conditions ...
Page 8
Backlight driving The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. condition:IL=6.0mA,Ta=25℃±2℃,FL=60kHz.) Parameter ...
Page 9
Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2 - ①∼③ . 7-1. Timing characteristics Parameter Clock Frequency High time Low time Data Setup time Hold time Horizontal Cycle sync. signal Pulse width Vertical ...
Page 10
Vertical display position The vertical display position is automatically centered in the active area at each mode of VGA ,480-,400-,and 350-line mode . Each mode is selected depending on the polarity of the synchronous signals described in 4-1(Note1). In ...
Page 11
THp Horizontal 0.7Vcc sync. signal 0.3Vcc 0.3Vcc (Hsync) THc * Only when enable terminal is fixed "Low" Clock signal 0.3Vcc 0.3Vcc 0.3Vcc 0.3Vcc (CK) C1* C2* Data signal (R0~R5,G0~G5, Horizontal invalid da ta period B0~B5) THe 0.7Vcc Data enable signal ...
Page 12
THp Horizontal 0.7Vcc 0.3Vcc 0.3Vcc sync. signal (Hsync) THc * Only when enable terminal (ENAB) is fixed "Low" Clock signal 0.3Vcc 0.3Vcc 0.3Vcc (CK) C1* C2* Number of clock Data signal (R0~R5,G0~G5, Horizontal data invalid B0~B5) period THe 0.7Vcc Data ...
Page 13
Horizontal 0.3Vcc sync. signal (Hsync) THp THc * Only when enable terminal (ENAB) fixed to "Low" Clock signal 0.3Vcc 0.3Vcc 0.3Vcc (CK) C1* C2* Number of clock Data signal (R0~R5,G0~G5, Horizontal invalid data period B0~B5) THe 0.7Vcc Data ...
Page 14
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale R0 R1 Gray Scale − Black 0 − Blue 0 − Green 0 − Cyan 0 − Red 1 − Magenta 1 − Yellow ...
Page 15
Optical Characteristics Parameter Horizontal θ21,θ22 ＣＲ＞１０ Viewing Angle Vertical Range Contrast ratio Response Rise Time Decay Chromaticity of White Luminance of white White Unifomity ※ The measurement shall be executed 30 minutes after The optical characteristics shall be measured ...
Page 16
The contrast ratio is defined as the following. Contrast Ratio (CR) ＝ 【Note3】Definition of response time: The response time is defined as the following figure and shall be measured by switching ...
Page 17
Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 11．Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure ...
Page 18
... Pulse width : 11ms, half sine wave Direction : ±X,±Y,±Z once for each direction. Packing box ①Model.No ②Shipment Date ③Quantity （４Ｓ）LQ10D421 社内品番： Model No. Lot No. ＬｏｔＮＯ． Ｑｕａｎｔｉｔｙ： ...
Page 19
LD12610B-17 ...
Page 20
Fig.4 Packing Form LD12610B-18 ...
Page 21
... Fig.1 LQ10D421 Outline Dimensions LD12610B-19 ...
Page 22
... Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Electronics (Singapore) PTE., Ltd. ...