M7E12HRN2 Omron, M7E12HRN2 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
M7E12HRN2
Manufacturer Part Number
M7E12HRN2
Description
Manufacturer
Omron
Datasheet
1.M7E12HRN2.pdf
(11 pages)
Specifications of M7E12HRN2
Display Type
Segmented
Emitting Color
Red
Number Of Digits
1
Package Type
Module
Operating Temperature Classification
Commercial
Opto Display Type
Module
Pattern Type
Segmented
Lead Free Status / Rohs Status
Compliant
■ Serial Transmission with B7A Link Terminal
A series of models incorporating a communications (serial transmission) function is available.
By using the B7A Link Terminal (PLC connector model), the Units can be connected to the PLC with ease. The 16-point B7A Link Terminal allows
the control of a maximum of four digits over two wires.
Available Link Terminal Models
Transmission Path
Transmission distance:
A maximum transmission distance of 500 m is
possible by using the VCTF 0.75 x 2C Cable if
power is supplied independently to the Input and
Output Link Terminals.
A maximum transmission distance of 100 m is
possible by using the VCTF 0.75 x 3C Cable if a
single power supply is connected to the Input or
Output Link Terminal, in which case the current
flow on the power lines (positive and negative
lines) is 1.8 A maximum.
Transmission delay:
A maximum of 50 ms for data display after the
B7A's input signal becomes definite.
Minimum Input Time
Use an input time of 80 ms min. to the Input
Unit for the B7A.
Power Supply Placed Only on the Receiving Side
Power Supplies Placed on Both the Transmitting and Receiving Sides
B7A-T10S1
B7A-T10S3
B7A-T10M2
B7A-T6A1
B7A-T6B1
B7A-T6C1
B7A-T6D2
B7A-T6E3
B7A-T3E3 (See note 2.)
C200H-B7A (See note 3.)
CQM1-B7A (See note 3.)
CJ1W-B7A (See note 3.)
CS1W-B7A (See note 3.)
Transmission side
M7E-08/12/20
M7E-08/12/20
Screw terminal model
Screw terminal model
Module model
Screw terminal model
Screw terminal model
Screw terminal model
Module model
Connector model
Connector model
Screw terminal model
Screw terminal model
Screw terminal model
Screw terminal model
Wiring
10
10
10
16
16
16
16
16
32
16 × @ ports
16 × @ ports
16 × @ ports
16 × @ ports
No. of I/O points
Signal Allocation
B7A-M7E Corresponding Pin List
The B7A's switch terminals correspond to the
M7E's parallel input signals as follows:
Note: A maximum of two Display Units can be
B7A switch terminal
24-VDC
power
supply
24-VDC
power
supply
connected when the 10-point B7A Link
Terminal is used and a maximum of four
Display Units can be connected when the
16-point B7A Link Terminal is used.
Transmission distance: 500 m max.
A10
A11
A12
A13
A14
A15
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Transmission distance: 100 m max.
2
2
2
4
4
4
4
4
8
4 × @ ports
4 × @ ports
4 × @ ports
4 × @ ports
Connectable M7E
Display Units
First digit
(1's digit)
Second digit
(10's digit)
Third digit
(100's digit)
Fourth digit
(1000's digit)
M7E parallel input
Note: 1. Use the B7A Link Terminal with a normal I/O delay of
(12 to 24 V)
DC power
supply
2. The connection of the 32-point connector model is as
3. For details on corresponding models, refer to each
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
19.2 ms. The B7A with short I/O delay cannot be used.
follows:
applicable model’s catalog.
B7A
(PLC connector model)
B7A
(PLC connector model)
PLC
connector
model 32
points
Units can be
connected easily
with the dedicated
harness.
Errors
1. No signal transmission is available due to the
2. The waveform is greatly distorted due to
Error Indication
When an error results, “-” will be displayed and
the display will flash. After the condition returns to
normal, reception data will be displayed.
Display after Error
Correction
After the condition returns to normal, the display
will be reset automatically and reception data will
be displayed.
SIG1
SIG2
disconnection of the transmission path (the SI
or GND wire).
external noise interference or because the
transmission path is longer than the
permissible transmission path.
PLC
PLC
M7E
6