E2C-EM07M Omron, E2C-EM07M Datasheet - Page 11

• Manufacturer Part Number: E2C-EM07M
• Description: Proximity Sensors Prox Switch
• Manufacturer: Omron
• Series: E2Cr

Specifications of E2C-EM07M

• Proximity Sensor Sensing Distance: 7mm
• Proximity Sensor Sensing Distance Range: 7 to 15mm
• Mounting: Din-Rail
• Operating Temp Range: -10C to 60C
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 12V
• Operating Supply Voltage (typ): 12/15/18/24V
• Operating Supply Voltage (max): 26.4V
• Pin Count: 4
• Maximum Operating Temperature: + 60 C
• Supply Voltage: 12 V to 24 V
• Mounting Style: DIN Rail
• Sensing Distance: 7 mm
• Minimum Operating Temperature: - 10 C
• Sensor Type: Inductive
• Sensing Object: Metallic
• Response Frequency: -
• Material - Body: Brass
• Shielding: Unshielded
• Voltage - Supply: -
• Output Type: -
• Terminal Type: Connector
• Package / Case: Cylinder, Threaded - M18
• Lead Free Status / Rohs Status: Compliant

Separate Amp/
Rectangular
858
Proximity
Information
Cylindrical
Capacitive
Peripheral
E2C-EDA
E2C-EDA
Sensors
Connector
/E2C-H
Pre-wired
Sensing
Devices
General
E2EC
E2CY
Models
Models
Models
Others
E2C
Guide
Models
E2C-EDA
Safety Precautions
Refer to Warranty and Limitations of Liability on page F-2.
This product is not designed or rated for ensuring
safety of persons. Do not use it for such purposes.
Do not use the Encoder under ambient conditions that exceed the
ratings.
Amplifier Units
● Design
Power ON
The Sensor is ready to sense an object within 200 ms after turning the
power ON. If the load and Sensor are connected to different power
supplies, always turn ON the Sensor power first.
● Mounting
Connecting and Disconnecting Sensor Heads
(1) Open the protective cover.
(2) Making sure that the lock button on the Sensor Head connector is
To disconnect the Sensor Head, pull out the fibers while pressing on
the lock button.
up, insert the fibers all the way to the back of the connector
insertion opening.
2
Precautions for Correct Use
1
Lock button
WARNING
Connecting and Disconnecting Connectors
Connecting
(1) Insert the Master or Slave Connector into the Amplifier Unit until it
(2) Apply the enclosed seal to the unconnected surface of the Master/
Note: Apply the seal to the grooved side.
Disconnecting
(1) Slide the Slave Amplifier Unit.
(2) After the Amplifier Unit has been separated, press down on the
Installing and Removing Amplifier Units
Installing
(1) Install the Units one by one on the DIN Track.
(2) Slide one Unit toward the other, match the clips at the front ends,
Removing
Slide one Unit away from the other and remove them one by one.
(Do not remove the connected Units together from the DIN Track.)
Note: 1. When the Amplifier Units are connected to each other, the operable
Sensor Head connector clips
clicks into place.
Slave Connector.
lever on the connector and remove the connector. (Do not attempt
to remove the connector without separating it from the other
Amplifier Unit first.)
and then bring them together until they click into place.
2. Before connecting or disconnecting the Units, always turn OFF the
ambient temperature changes depending on the number of connected
Amplifier Units. Check Ratings and Specifications on page 853.
power.
DIN Track
Power supply connector
2
1
Protector seal
2
Insert
Press down
DIN Track
1
1
Remove
Lever