TOTX147PLF,T Toshiba, TOTX147PLF,T Datasheet - Page 4

• Manufacturer Part Number: TOTX147PLF,T
• Manufacturer: Toshiba

Specifications of TOTX147PLF,T

• Optical Fiber Type: TX
• Data Transfer Rate: 15Mbps
• Operating Temperature Classification: Commercial
• Peak Wavelength: 650nm
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -20C to 70C
• Mounting: Snap in
• Pin Count: 5
• Lead Free Status / Rohs Status: Compliant

(6)
(7)
(8)
(9)
(10) Soldering condition
(11) Case(receptacle) material
(12) Precautions when disposing of devices and packing materials.
(13) Precautions during use
Attaching the fiber optic receiving module
Solder the fixed pins (pins 4 and 5) of the fiber optic receiving module TOTX147PL(F,T) to the printed
circuit board in order to fix it to the board.
Solvent
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to
pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off
using cotton tips.
Supply voltage
Use the supply voltage within the recommended operating condition (V
that supply voltage does not exceed the maximum rating value of 4.5 V, even for an instant.
Input voltage
If a voltage exceeding the maximum rating value (V
the internal IC may suffer damage. If there is a possibility that excessive voltage due to surges may
be added to the input terminal, insert a protective circuit.
Solder at 260°C or less for no more than ten seconds.
When disposing devices and packing materials, follow the procedures stipulated by local regulations
in order to protect the environment against contamination.
Compound semiconductors such, as GaAs are used as LED materials in this module. When devices
are disposed of, worker safety and protection of the environment must be taken into account.
Toshiba is continually working to improve the quality and reliability of their products. Nevertheless,
semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity
and their vulnerability to physical stress. It is the responsibility of the buyer, when utilizing Toshiba
products, to observe standards of safety, and to avoid situations in which the malfunction or failure of
a Toshiba product could cause loss of human life, bodily injury or damage to property.
When developing equipment, please ensure that Toshiba products are used within the specified
operating ranges set forth in the most recent product specifications. Also, please keep in mind the
precautions and conditions set forth in the Toshiba Semiconductor Reliability Handbook.
The case is made of polycarbonate. Polycarbonate is usually stable with acid, alcohol, and
aliphatic hydrocarbons however, with petrochemicals (such as benzene, toluene, and acetone),
alkali, aromatic hydrocarbons, or chloric hydrocarbons, polycarbonate becomes cracked, swollen,
or melted. Please take care when choosing a packaging material by referencing the table below.
〈Chemicals to avoid with polycarbonate〉
A
B
C
D
Little deterioration
But staining
Cracked crazed,
Melted
｛ ｝ ：used as solvent
Decomposed
or Swollen
PHENOMENON
・nitric acid(low concentration) , hydrogen peroxide, chlorine
・acetic acid(70% or more)
・gasoline
・methyl isobutyl ketone, ethyl acetate, butyl acetate
・methyl methacrylate, ethyl ether, MEK
・acetone, m-amino alcohol, carbon tetrachloride
・carbon disulfide, trichloroethylene, cresol
・thinners, oil of turpentine
・triethanolamine
・concentrated sulfuric acid
・benzene
・styrene, acrylonitrile, vinyl acetate
・ethylenediamine, diethylenediamine
・{chloroform, methyl chloride, tetrachloromethane, dioxane}
・ammonia water
・other alkali
{1,2-dichloroethane}
4
CC
+ 0.5 V) is applied to the transmitters' input,
CHEMICALS
CC
= 2.7 to 3.6 V). Make sure
TOTX147PL(F,T)
2006-12-28