LTC2640AITS8-HZ12#TRPBF Linear Technology, LTC2640AITS8-HZ12#TRPBF Datasheet - Page 9
![IC DAC 12BIT VOUT W/REF TSOT23-8](/photos/6/59/65931/tsot-23-8_05-08-1637_sml.jpg)
LTC2640AITS8-HZ12#TRPBF
Manufacturer Part Number
LTC2640AITS8-HZ12#TRPBF
Description
IC DAC 12BIT VOUT W/REF TSOT23-8
Manufacturer
Linear Technology
Datasheet
1.LTC2640CTS8-HM10TRMPBF.pdf
(24 pages)
Specifications of LTC2640AITS8-HZ12#TRPBF
Settling Time
4.1µs
Number Of Bits
12
Data Interface
Serial
Number Of Converters
1
Voltage Supply Source
Single Supply
Power Dissipation (max)
450µW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
TSOT-23-8, TSOT-8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
TIMING CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
SYMBOL
e
SYMBOL
t
t
t
t
t
t
t
t
t
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltages are with respect to GND.
Note 3: High temperatures degrade operating lifetimes. Operating lifetime
is derated at temperatures greater than 105°C.
Note 4: Linearity and monotonicity are defi ned from code k
2
rounded to the nearest whole code. For V
and linearity is defi ned from code 26 to code 4,095. For V
and N = 12, k
Note 5: Inferred from measurement at code 16 (LTC2640-12), code 4
(LTC2640-10) or code 1 (LTC2640-8), and at full-scale.
temperature range, otherwise specifi cations are at T
LTC2640-HM12/-HM10/-HM8/-HZ12/-HZ10/-HZ8, LTC2640A-HM12/-HZ12 (V
range, otherwise specifi cations are at T
LTC2640-HM12/-HM10/-HM8/-HZ12/-HZ10/-HZ8, LTC2640A-HM12/-HZ12 (V
1
2
3
4
5
6
7
9
10
n
N
– 1, where N is the resolution and k
L
= 16 and linearity is defi ned from code 16 to code 4,095.
PARAMETER
SDI Valid to SCK Setup
SDI Valid to SCK Hold
SCK High Time
SCK Low Time
CS/LD Pulse Width
LSB SCK High to CS/LD High
CS/LD Low to SCK High
CLR Pulse Width
CS/LD High to SCK Pos. Edge
SCK Frequency
PARAMETER
Output Voltage Noise Density
Output Voltage Noise
L
is given by k
FS
= 2.5V and N = 12, k
A
= 25°C. V
L
= 0.016 • (2
FS
CC
L
The
= 4.096V
A
to code
= 4.5V to 5.5V. (See Figure 1) (Note 8).
CONDITIONS
At f = 1kHz, External Reference
At f = 10kHz, External Reference
At f = 1kHz, Internal Reference
At f = 10kHz, Internal Reference
0.1Hz to 10Hz, External Reference
0.1Hz to 10Hz, Internal Reference
0.1Hz to 200kHz, External Reference
0.1Hz to 200kHz, Internal Reference,
C
= 25°C. V
REF
l
L
= 26
N
denotes the specifi cations which apply over the full operating temperature
= 0.33μF
/ V
The
FS
CONDITIONS
50% Duty Cycle
),
l
CC
denotes the specifi cations which apply over the full operating
= 4.5V to 5.5V, V
Note 6: This IC includes current limiting that is intended to protect the
device during momentary overload conditions. Junction temperature can
exceed the rated maximum during current limiting. Continuous operation
above the specifi ed maximum operating junction temperature may impair
device reliability.
Note 7: Digital inputs at 0V or V
Note 8: Guaranteed by design and not production tested.
Note 9: Internal Reference mode. DAC is stepped 1/4 scale to 3/4 scale
and 3/4 scale to 1/4 scale. Load is 2k in parallel with 100pF to GND.
Note 10: Temperature coeffi cient is calculated by dividing the maximum
change in output voltage by the specifi ed temperature range.
Note 11: Full-scale error is determined using the reference voltage
measured at the REF pin.
FS
FS
= 4.096V)
= 4.096V)
OUT
unloaded unless otherwise specifi ed.
l
l
l
l
l
l
l
l
l
l
CC
.
MIN
MIN
10
20
4
4
9
9
7
7
7
TYP
140
130
210
200
650
670
20
20
TYP
LTC2640
MAX
MAX
50
nV√Hz
nV√Hz
nV√Hz
nV√Hz
UNITS
UNITS
μV
μV
μV
μV
2640fb
9
MHz
P-P
P-P
P-P
P-P
ns
ns
ns
ns
ns
ns
ns
ns
ns