MAX536BCPE Maxim Integrated Products, MAX536BCPE Datasheet - Page 13

• Manufacturer Part Number: MAX536BCPE
• Description: IC DAC QUAD CALBRTD 12BIT 16-DIP
• Manufacturer: Maxim Integrated Products

Specifications of MAX536BCPE

• Settling Time: 3µs
• Number Of Bits: 12
• Data Interface: Serial
• Number Of Converters: 4
• Voltage Supply Source: Dual ±
• Power Dissipation (max): 842mW
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

The input impedance at each reference input is code
dependent, ranging from a low value of typically 6k
(with an input code of 0101 0101 0101) to a high value
of 60k
the input impedance at the reference pins is code
dependent, load regulation of the reference source is
important.
The REFAB and REFCD reference inputs have a 5k
guaranteed minimum input impedance. When the two
reference inputs are driven from the same source, the
effective minimum impedance becomes 2.5k . A volt-
age reference with a load regulation of 0.001%/mA,
such as the MAX674, would typically deviate by
0.164LSB (0.328LSB worst case) when simultaneously
driving both MAX536 reference inputs at 10V.
An op amp, such as the MAX400 or OP07, can be used
to buffer the reference to increase reference accuracy.
The op amp’s closed-loop output impedance should be
kept below 0.05
0.08LSB. Reference accuracy is also improved by driv-
ing the REFAB and REFCD pins separately, or by using
a reference with excellent accuracy and superior load
regulation, such as the MAX676/MAX677/MAX678.
The reference input capacitance is also code depen-
dent and typically ranges from 125pF to 300pF.
Figure 2. Connections for Microwire
*THE SDO-SI CONNECTION IS NOT REQUIRED FOR WRITING TO THE MAX536,
**THE LDAC CONNECTION IS NOT REQUIRED WHEN USING THE 3-WIRE INTERFACE.
† THE MAX537 HAS AN INTERNAL ACTIVE PULL-UP TO V
BUT MAY BE USED FOR READBACK PURPOSES.
SO R
P
MAX536
MAX537
IS NOT NECESSARY.
(with an input code of 0000 0000 0000). Since
Voltage-Output DACs with Serial Interface
LDAC**
_______________________________________________________________________________________
SDO*
SCK
SDI
CS
5V
to ensure an error of less than
† R
P
1k
SK
SO
SI*
I/O
I/O
DD,
MICROWIRE
PORT
Calibrated, Quad, 12-Bit
All MAX536/MAX537 voltage outputs are internally
buffered by precision unity-gain followers with a typical
slew rate of 5V/ s for the MAX536 and 3V/ s for the
MAX537.
With a full-scale transition at the MAX536 output (0V to
10V or 10V to 0V), the typical settling time to ±1/2LSB is
3 s when loaded with 5k
less than 5k degrade performance).
With a full-scale transition at the MAX537 output (0V to
2.5V or 2.5V to 0V), the typical settling time to ±1/2LSB
is 5 s when loaded with 5k
(loads less than 5k degrade performance).
Output dynamic responses and settling performances
of the MAX536/MAX537 output amplifier are shown in
the Typical Operating Characteristics .
The MAX536/MAX537’s 3-wire or 4-wire serial interface is
compatible with both Microwire (Figure 2) and SPI/QSPI
(Figure 3). In Figures 2 and 3,
high or low for a 3-wire interface, or used as the fourth
input with a 4-wire interface. The connection between
SDO and the serial-interface port is not necessary, but
may be used for data echo. (Data held in the shift register
Figure 3. Connections for SPI/QSPI
*THE SDO-MISO CONNECTION IS NOT REQUIRED FOR WRITING TO THE MAX536,
**THE LDAC CONNECTION IS NOT REQUIRED WHEN USING THE 3-WIRE INTERFACE.
† THE MAX537 HAS AN INTERNAL ACTIVE PULL-UP TO V
BUT MAY BE USED FOR READBACK PURPOSES.
SO R
P
MAX536
MAX537
IS NOT NECESSARY.
LDAC**
Serial-Interface Configurations
SDO*
SCK
SDI
CS
Output Buffer Amplifiers
† R
P
in parallel with 100pF (loads
5V
1k
LDAC
in parallel with 100pF
CPOL = 0, CPHA = 0
MISO*
MOSI
SCK
I/O
I/O
DD,
can be tied either
SPI/QSPI
PORT
SS
13