1-770903-0 TE Connectivity, 1-770903-0 Datasheet
1-770903-0
Specifications of 1-770903-0
Available stocks
Related parts for 1-770903-0
1-770903-0 Summary of contents
Page 1
... This specification covers performance, tests and quality requirements for MATE-N-LOK* mini-universal connectors. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line was completed on 02Aug04 ...
Page 2
... Temperature: -55 to 105° C 3.4. Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per EIA-364. 3.5. Test Requirements and Procedures Summary Test Description Initial examination of product ...
Page 3
... See Note. No discontinuities of 10 microseconds or longer duration. See Note. See Note. Contacts shall not dislodge. See Note. 13 lbf] maximum per contact. TE Spec 109-41. 6.7 N [1.5 lbf] maximum per circuit initial. 0.7 N [.15 lbf] minimum per circuit final lbf] minimum. 133.4 N [30 lbf]. ...
Page 4
... See Note. Figure 1 (end) 108-1542 Procedure EIA-364-31, Method III. Subject specimens to 10 cycles (10 days) between 25 and 65° 100% RH. EIA-364-17, Method A, Test Condition 4. Subject mated specimens to 105° C for 580 hours. EIA-364-65, Class IIA (4 gas). Subject mated specimens to environmental Class IIA for 20 days ...
Page 5
... Final examination of product (a) See paragraph 4.1.A. NOTE (b) Numbers indicate sequence in which tests are performed. (c) Discontinuities shall not be measured. Energize at 18 Quality Specification 102-950. th (d) The 4 test in this sequence shall be either humidity/temperature cycling for tin plated specimens or mixed flowing gas for gold plated specimens. Precondition specimens with 5 durability cycles ...
Page 6
... Temperature life Mixed flowing gas Final examination of product (a) See paragraph 4.1.A. NOTE (b) Numbers indicate sequence in which tests are performed. (c) Discontinuities shall not be measured. Energize at 18 per Quality Specification 102-950. (d) Precondition specimens with 5 durability cycles. Rev D Test Group (a) Test or Examination 1 Test Sequence (b) ...
Page 7
... Acceptance Acceptance is based on verification that the product meets the requirements of Figure 1. Failures attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to confirm corrective action is required before resubmittal ...
Page 8
... Base rated Current for a single circuit at the maximum ambient operating temperature shown in Figures 4A. Test Reports CTL1314-004 and CTL7166-007 Rev Ambient Temperature (C) Figure 4A Current Carrying Capability (11.21 amperes) Percent Connector Loading Single 47% Brass/Tin Pin and Socket 1.00 .668 .248 ...
Page 9
... Base rated Current for a single circuit at the maximum ambient operating temperature shown in Figures 4C. Rev D Figure 4C Current Carrying Capability (8.55 amperes) Test Report EA20100461T Percent Connector Loading Single 47% Palladium Nickle Pin and Socket 1.00 .699 Figure 4D Current Rating Test Report EA20100461T 108-1542 100% .528 ...
Page 10
... Rev D Figure 5 Vibration Mounting Fixture Figure 6 Mechanical Shock Mounting Fixture 108-1542 ...