104479-8 TE Connectivity, 104479-8 Datasheet - Page 2

• Manufacturer Part Number: 104479-8
• Description: CONTACT, RECEPTACLE, 24-20AWG, CRIMP
• Manufacturer: TE Connectivity
• Series: AMPMODU Short Pointr

Specifications of 104479-8

• Connector Type: Contact, Crimp
• Current Rating: 3A
• Contact Plating: Tin
• Contact Material: Copper Alloy
• Rohs Compliant: Yes
• Product Type: Contact
• Termination Method To Wire/cable: Crimp
• Wire Insulation Diameter (mm [in]): 0.64 – 1.52 [0.025 – 0.060]
• Connector Series: Short Point
• With Insulation Support: Yes
• Applied Pressure: Standard
• Contact - Rated Current (a): 3
• Voltage Rating (vac): 300
• Termination Resistance (m?): 12
• Insulation Resistance (m?): 5,000
• Dielectric Withstanding Voltage (v): 750
• Crimp Area Plating: Tin
• Wire Range (mm [awg]): 0.20-0.60² [24-20]
• Contact Type: Socket
• Contact Plating, Mating Area, Material: Tin
• Contact Base Material: Copper Alloy C7025
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Approved Standards: UL E28476, CSA LR7189
• Operating Temperature (°c): -65 – +105
• Applies To: Wire/Cable
• Packaging Method: Strip
• For Use With: AMPMODU Short Point Connectors

3.4.
3.5.
Examination of product.
Termination resistance.
Insulation resistance.
Dielectric withstanding voltage.
Vibration, sinusoidal.
Physical shock.
Durability.
Contact retention.
Rev A
Performance and Test Description
Product is designed to meet electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per Test Specification 109-1.
Test Requirements and Procedures Summary
Test Description
Meets requirements of product
drawing and Application
Specification 114-25038.
15 milliohms maximum initial.
20 milliohms maximum final.
5000 megohms minimum initial.
1000 megohms minimum final.
No discontinuities of 1 microsecond
or longer duration.
See Note.
No discontinuities of 1 microsecond
or longer duration.
See Note.
See Note.
Contacts shall not dislodge.
Test Voltage
750
300
275
Figure 1 (continued)
MECHANICAL
ELECTRICAL
Requirement
Altitude, Feet
Sea level
50000
70000
Visual, dimensional and functional
per applicable quality inspection
plan.
TE Spec 109-6-1.
Subject mated contacts assembled
in housing to 50 mv maximum open
circuit at 100 ma maximum.
See Figure 3.
TE Spec 109-28-4.
Test between adjacent contacts of
samples.
TE Spec 109-29-1.
Test between adjacent contacts of
samples.
TE Spec 109-21-3.
Subject mated samples to 15 G’s
between 10-2000-10 Hz traversed
in 20 minutes. 4 hours in each of 3
mutually perpendicular planes.
See Figure 4.
TE Spec 109-26-7.
Subject mated samples to 50 G's
sawtooth shock pulses of 11
milliseconds duration. 3 shocks in
each direction applied along 3
mutually perpendicular planes, 18
total shocks.
See Figure 4.
TE Spec 109-27.
Mate and unmate samples for 200
cycles for 30 µin gold plating, 75
cycles for 15 µin gold plating, and
25 cycles for tin-lead plating at
maximum rate of 200 cycles per
hour.
TE Spec 109-30.
Apply axial load of 3 pounds to
contacts.
Procedure
108-1472
2 of 6