AD5662ARMZ-1 Analog Devices Inc, AD5662ARMZ-1 Datasheet - Page 17

• Manufacturer Part Number: AD5662ARMZ-1
• Description: IC DAC 16BIT BUFF V-OUT 8-MSOP
• Manufacturer: Analog Devices Inc
• Series: nanoDAC™r

Specifications of AD5662ARMZ-1

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Design Resources: 4 mA to 20 mA Process Control Loop Using AD5662 (CN0009) 16-Bit Fully Isolated Voltage Output Module Using AD5662, ADuM1401, and External Amplifiers (CN0063) 16-Bit Fully Isolated 4 mA to 20 mA Output Module Using AD5662, ADuM1401, and External Amplifiers (CN0064)
• Settling Time: 8µs
• Number Of Bits: 16
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 750µW
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Resolution (bits): 16bit
• Sampling Rate: 125kSPS
• Input Channel Type: Serial
• Supply Voltage Range - Analog: 2.7V To 5.5V
• Supply Current: 150µA
• Digital Ic Case Style: SOP
• Number Of Channels: 1
• Resolution: 16b
• Conversion Rate: 1.2MSPS
• Interface Type: SER 3W SPI QSPI UW
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: Resistor-String
• Power Supply Requirement: Single
• Output Type: Voltage
• Integral Nonlinearity Error: ±32+/- LSB
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: MSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD5662 to 80C51/80L51 Interface
Figure 39 shows a serial interface between the AD5662 and the
80C51/80L51 microcontroller. The setup for the interface is as
follows. TxD of the 80C51/80L51 drives SCLK of the AD5662,
while RxD drives the serial data line of the part. The SYNC
signal is again derived from a bit-programmable pin on the port.
In this case, port line P3.3 is used. When data is to be transmitted
to the AD5662, P3.3 is taken low. The 80C51/80L51 transmits
data in 8-bit bytes only; thus only eight falling clock edges occur
in the transmit cycle. To load data to the DAC, P3.3 is left low
after the first eight bits are transmitted, and a second write cycle
is initiated to transmit the second byte of data. P3.3 is taken
high following the completion of this cycle. The 80C51/80L51
outputs the serial data in a format that has the LSB first. The
AD5662 must receive data with the MSB first. The 80C51/80L51
transmit routine should take this into account.
*ADDITIONAL PINS OMITTED FOR CLARITY
80C51/80L51*
Figure 39. AD5662 to 80C51/80L51 Interface
P3.3
RxD
TxD
AD5662*
SYNC
SCLK
DIN
Rev. A | Page 17 of 24
AD5662 to MICROWIRE Interface
Figure 40 shows an interface between the AD5662 and any
MICROWIRE-compatible device. Serial data is shifted out on
the falling edge of the serial clock and is clocked into the AD5662
on the rising edge of the SK.
*ADDITIONAL PINS OMITTED FOR CLARITY
MICROWIRE*
Figure 40. AD5662 to MICROWIRE Interface
SO
CS
SK
AD5662*
SYNC
SCLK
DIN
AD5662