X9315UM-2.7T1 Intersil, X9315UM-2.7T1 Datasheet - Page 4
![IC XDCP 32-TAP 50K 3WIRE 8-MSOP](/photos/6/65/66540/20-8-msop_sml.jpg)
X9315UM-2.7T1
Manufacturer Part Number
X9315UM-2.7T1
Description
IC XDCP 32-TAP 50K 3WIRE 8-MSOP
Manufacturer
Intersil
Series
XDCP™r
Datasheet
1.X9315WS.pdf
(16 pages)
Specifications of X9315UM-2.7T1
Taps
32
Resistance (ohms)
50K
Number Of Circuits
1
Temperature Coefficient
300 ppm/°C Typical
Memory Type
Non-Volatile
Interface
Up/Down (3-Wire)
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Resistance In Ohms
50K
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
X9315UM-2.7T1
Manufacturer:
TI/BB
Quantity:
7 500
Part Number:
X9315UM-2.7T1
Manufacturer:
XICOR
Quantity:
20 000
Pin Configuration
Pin Names
Pin Description
R
The high (R
are equivalent to the fixed terminals of a mechanical
potentiometer. The minimum voltage is V
maximum is V
references the relative position of the terminal in relation to
wiper movement direction selected by the U/D input, and not
the voltage potential on the terminal.
R
R
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
The wiper terminal series resistance is typically 200Ω at
V
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
W
CC
W
H
/V
/V
/V
= 5V.
w
SYMBOL
H
W
R W /V W
R H /V H
R L /V L
is the wiper terminal and is equivalent to the movable
V CC
and R
V SS
U/D
INC
CS
H
R
H
/V
V
CC
INC
U/D
/V
L
SS
H
H
/V
) and low (R
. The terminology of R
(8 LD MSOP, SOIC, PDIP)
L
1
2
3
4
TOP VIEW
X9315
X9315
L
Chip Select control input
4
Increment control input
/V
Up/Down control input
L
DESCRIPTION
) terminals of the X9315
Supply voltage
Wiper terminal
High terminal
Low terminal
8
7
6
5
Ground
L
/V
SS
V
CS
R
R
L
CC
W
L
/V
and the
/V
and R
L
W
H
/V
H
X9315
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in nonvolatile memory when
CS is returned HIGH while the INC input is also HIGH. After
the store operation is complete the X9315 will be placed in
the low power standby mode until the device is selected
once again.
Principles of Operation
There are three sections of the X9315: the input control,
counter and decode section; the nonvolatile memory; and
the resistor array. The input control section operates just like
an up/down counter. The output of this counter is decoded to
turn on a single electronic switch connecting a point on the
resistor array to the wiper output. Under the proper
conditions the contents of the counter can be stored in
nonvolatile memory and retained for future use. The resistor
array is comprised of 31 individual resistors connected in
series. At either end of the array and between each resistor
is an electronic switch that transfers the connection at that
point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for t
R
a significant amount if the wiper is moved several positions.
When the device is powered-down, the last wiper position
stored will be maintained in the nonvolatile memory. When
power is restored, the contents of the memory are recalled
and the wiper is set to the value last stored.
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the device
is selected and enabled to respond to the U/D and INC
inputs. HIGH to LOW transitions on INC will increment or
decrement (depending on the state of the U/D input) a five
bit counter. The output of this counter is decoded to select
one of thirty two wiper positions along the resistive array.
The value of the counter is stored in nonvolatile memory
whenever CS transitions HIGH while the INC input is also
HIGH.
The system may select the X9315, move the wiper and
deselect the device without having to store the latest wiper
position in nonvolatile memory. After the wiper movement is
performed as described above and once the new position is
reached, the system must keep INC LOW while taking CS
HIGH. The new wiper position will be maintained until
TOTAL
value for the device can temporarily be reduced by
IW
(INC to V
W
change). The
December 21, 2009
FN8179.2